If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Dave on July 3, 2007, 11:26 am
Am dissatisfied, after living in my new home for 2 years. Home is on
concrete 12X12 piers/crawlspace, no slab. Live in central TX, very mild
winters. Yet, in the winter, the floor is very noticably cold.
During the build, I noticed they used rolled fiberglas insulation. Don't
know the "R" value, was thicker than what they put in the walls. They
cutout 2 sections, placed one on top of the other, then placed between floor
joists. They stapled the lower section to the floor joist. When they were
all done with the insulation, they used a nylon netting all over the bottom.
Stapled that to the floor joists. Floor joists are 2X12 under the house.
My opinion is was too loose fit, too much air travel in the joist insulated
area. Is there a fix for this?
Dave
|
|
Posted by RicodJour on July 3, 2007, 11:41 am
> Am dissatisfied, after living in my new home for 2 years. Home is on
> concrete 12X12 piers/crawlspace, no slab. Live in central TX, very mild
> winters. Yet, in the winter, the floor is very noticably cold.
> During the build, I noticed they used rolled fiberglas insulation. Don't
> know the "R" value, was thicker than what they put in the walls. They
> cutout 2 sections, placed one on top of the other, then placed between floor
> joists. They stapled the lower section to the floor joist. When they were
> all done with the insulation, they used a nylon netting all over the bottom.
> Stapled that to the floor joists. Floor joists are 2X12 under the house.
> My opinion is was too loose fit, too much air travel in the joist insulated
> area. Is there a fix for this?
You may have a problem with air infiltration. Get a smoke stick and
see if you can find where the air leaks are - there are always some.
Caulk the leaks and that should help some. It sounds like they put in
plenty of insulation, and it doesn't sound like there's much room for
air circulation in the joist bays. Problem is that insulation doesn't
create heat, it just slows the heat transfer. The floor will always
be colder unless you have a radiant floor.
R
|
| Similar Threads | Posted | | Subfloor framing. | August 19, 2006, 5:01 pm |
| subfloor attachments | November 25, 2006, 10:13 am |
| Level Plywood Subfloor | July 8, 2006, 2:22 am |
| foam subfloor adhesive | August 31, 2006, 9:33 pm |
| concrete filler around subfloor? | September 14, 2007, 7:50 pm |
| cat urine smell in subfloor | October 20, 2007, 10:24 pm |
| plywood subfloor question | December 22, 2007, 10:11 pm |
| Minimizing subfloor opening for stairs | June 8, 2007, 3:06 pm |
| Historic Home, sloping floors, new subfloor | February 24, 2007, 1:20 pm |
| Historic Home, sloping floors, new subfloor | February 24, 2007, 1:20 pm |
|
|
> concrete 12X12 piers/crawlspace, no slab. Live in central TX, very mild
> winters. Yet, in the winter, the floor is very noticably cold.
> During the build, I noticed they used rolled fiberglas insulation. Don't
> know the "R" value, was thicker than what they put in the walls. They
> cutout 2 sections, placed one on top of the other, then placed between floor
> joists. They stapled the lower section to the floor joist. When they were
> all done with the insulation, they used a nylon netting all over the bottom.
> Stapled that to the floor joists. Floor joists are 2X12 under the house.
> My opinion is was too loose fit, too much air travel in the joist insulated
> area. Is there a fix for this?