|
Building Construction - Building Construction Industry Discussions.
|
|
|
|
If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by bent on September 27, 2006, 2:37 am
I am just about to get some ceiling tiles for my basement. The last thing
I noticed was that they come in either 5/8", or 3/4" thickness, and since
the two were very similar in style, but had proportionately different prices
I suppose the price difference is due to the extra thickness. I'm in
Toronto as far as temp and humidity goes; its just a regular living space
add-on for bathroom, laundry, and summer bedroom. I am not committed yet to
2'x4', or 2'x2' size yet. Is it beneficial to pay more for the extra
thickness. Will they sag over time or anything. I've got about 20'x20'
divided throughout 5 areas.
The standard size cross tees, 2' or 4', lock in with pre-made tabs, but
they can lock in throughout the entire length of adjoining members in slots
every 6". Is it possible to modify the standard tee lengths using aviation
snips to make tabs so it would be possible to cut the tiles themselves to
say 2'x3', for example. Is this cleaner than having 6" borders, or is it
more trouble than its worth. Not really studied the problem. I've never
even seen tiles done, but I am handy, and I've got tools.
What do you think of the any added bonus to using the drop-fit type tiles in
the 2'x2' compared to the flat 2'x4'. Is this worth it? I would have to
use a razor blade. A sea of flat vs. having a little projection.
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
|
|
Posted by bent on September 27, 2006, 3:09 am
I've got a really good handle on how I can lay this out do this because I
can see it all in seconds using AutoCAD. After looking at it I don't think
I really need to worry about the 2nd Q about modifying the Tees, cause I
don't have any 6" borders. You could answer it, but I don't think I need to
know.
But a general impression about the stylin' 2'x2's , and certainly the 3/4"
vs. 5/8" thick is appreciated.
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
|
|
Posted by bent on September 28, 2006, 12:46 pm
Well i settled the 2x2 vs 2x4 problem,and I think it depends on the actual
size of the room(s) and the layout of each type as to how it turns out. I
think the drop-in is definetely potentially nicer, but that is balanced
against the above. I will always wonder, but I didn't cheap out to make a
decision.. AutoCAD does this perfectly fast and I think it is crucial to
see this on paper to make a decision. Then take it in your mind to the
location.
I may end up using a Main Tee as an odd (>4') cross Tee, which is a
different Q/A.
And I walked right buy the 1/2" tiles, the cheapest, the display on the end
of the aisle. So my only remaining question is 1/2", 5/8", or 3/4"? The
1/2" do seem to bow if you hold them up. But for me, for the exact same
pattern, I'm not gonna wanna spend 3x as much, for the 3/4" as the 1/2".
Especially since I'm gonna be fighting for every millimeter. This Q is
still open.
----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----
|
| Similar Threads | Posted | | Is this type of fan appropriate under roof vents in ceiling? | June 26, 2007, 2:06 pm |
| Tin Look Ceiling Tiles at only 1.75 US $ per SquareFoot ! | July 12, 2006, 12:57 am |
| Tin Look Ceiling Tiles at only 1.75 US $ per SquareFoot ! | July 12, 2006, 12:57 am |
| I'm wondering how much to sell some boxes of ceiling tiles for | May 28, 2007, 1:18 pm |
| Making thread on bars. | May 1, 2008, 8:47 am |
| pipes making noise all of a sudden | February 29, 2008, 8:22 am |
| Re: What tool would you recommend for making a 1/2" deep channel in plaster walls? | November 7, 2006, 9:03 am |
| help name this type of concrete drain | November 22, 2006, 1:04 am |
| need shoji type door kits | April 28, 2007, 1:12 am |
| Hardwod floor type question. | May 26, 2007, 2:19 am |
|
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap