Home Page link

installing masonite prehung doors

Home| Search | About
Login Password
Register Now! Lost Password?

Building Construction - Building Construction Industry Discussions. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
installing masonite prehung doors beerguzzler50 07-06-2007
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by on July 6, 2007, 10:18 am
I have 4 doors to install in my basement project. 2 doorways are 2x4
framed with 1/2" sheetrock on both sides and 2 are 2x3 framed with
1/2" sheetrock also.

Is there a recommended way to trim the width of the doorjams so that
they are flush with the walls? don't know if I am using the right
terminology or not. I am guessing I want the door jams exactly flush
with the sheetrock so that the trim look good.

Thanks.


Posted by Pelletier on July 6, 2007, 10:28 am
On Jul 6, 10:18 am, beerguzzle...@yahoo.com wrote:
> I have 4 doors to install in my basement project. 2 doorways are 2x4
> framed with 1/2" sheetrock on both sides and 2 are 2x3 framed with
> 1/2" sheetrock also.
>
> Is there a recommended way to trim the width of the doorjams so that
> they are flush with the walls? don't know if I am using the right
> terminology or not. I am guessing I want the door jams exactly flush
> with the sheetrock so that the trim look good.
>
> Thanks.

Good eye/hand coordination and a skill saw is all i can come up
with :)


Posted by RicodJour on July 6, 2007, 10:49 am
On Jul 6, 10:18 am, beerguzzle...@yahoo.com wrote:
> I have 4 doors to install in my basement project. 2 doorways are 2x4
> framed with 1/2" sheetrock on both sides and 2 are 2x3 framed with
> 1/2" sheetrock also.
>
> Is there a recommended way to trim the width of the doorjams so that
> they are flush with the walls? don't know if I am using the right
> terminology or not. I am guessing I want the door jams exactly flush
> with the sheetrock so that the trim look good.
>
> Thanks.

You don't want the jamb exactly flush. It's good in theory, but you
need a bit of room to compensate for irregularities in the wall
surface. Generally ~ 1/6" on each side of the door. Factory jambs
are typically 1/16" over the nominal wall thickness.

Cut from the back side of the jamb, and cut off the side that is not
flush with the door face. Use a circular saw with an edge guide.
Don't cut right up to the line, leave a little bit and use a hand
plane to smooth out the edge of the jamb. Rock the plane a little bit
- just a few degrees to the outside of the jamb so that there's a
small bevel on the jamb. This allows the trim to sit tight against
the jamb at the inside edge of the trim. Lightly round over the sharp
exposed corner on the jamb before installing the trim.

R


Similar ThreadsPosted
I need Masonite Sideing!! April 18, 2007, 9:14 pm
reversing swing of prehung door November 27, 2006, 11:34 am
Doors (all in) July 3, 2006, 10:03 am
2x6 Interior Doors July 18, 2006, 9:55 am
1950's doors October 26, 2006, 2:14 am
Two Garage Doors Into One? October 26, 2007, 9:18 pm
Compact doors June 4, 2008, 6:14 pm
need sliding closet doors April 26, 2007, 1:02 am
Need Quality UPVC Doors in UK April 22, 2008, 4:08 am
Reversing a door swing or buy new prehung door January 23, 2008, 2:28 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap