Home Page link

well pressure gauge

Building Construction - Building Construction Industry Discussions. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
well pressure gauge bodega 03-14-2007
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by bodega on March 14, 2007, 4:23 pm
I left my garden hose from my well filling my new septic-tanks for the
pump test. I needed to do this for the county inspector. My neighbor
offered to shut the water off when one of the tanks(the one with the
pump) reached 3/4 full(approx. 900 gals.) I left and he forgot so when
I returned 2 days later both tanks were overflowing and the well pump
was still running.
Since then the pressure tank gauge in the well house never goes over
40 lbs. of pressure. It use to go up to 60 lbs. and then back down to
40 lbs. when water was running, then build up to 60 lbs. again when
the water was not being used. The water pressure at the hose seems to
be about the same as before this happened.
Is it possible that the gauge or something else went haywire when that
greater-than-usual demand was placed on the well?
Any suggestions will be appreciated. Thanks, Jack


Posted by Noncompliant on March 18, 2007, 8:41 am
Hopefully, the installer of the pump and reserve tank put in some cutoff
valves in the system. If so, there should be a cutoff valve leading toward
the house. Close this. If the pressure rises on the gauge you mentioned,
you got a leak some place on the other side of the cutoff valve. If not,
could be the gauge or the regulator for the pump.

Another way using your hearing. There should be a garden hose outlet on the
reserve tank. Close the cutoff valve previously mentioned for a few
minutes. Drain the reserve tank to the ground outside the well house for
minute or so. Close the valve on the reserve tank feeding the garden hose.
Watch the gauge and listen for a clunk sound inside the well house. The
sound means the pump has finished pumping. There could be debris right at
the gauge entry point, trapped there. Close the hopefully existing valve
that leads to reserve tank from the pump surface outlet and regulator. Kill
the power to the regulator and pump. Remove the gauge and inspect, clean if
needed. Replace if needed. Reinstall the gauge. Activate power and open
the valve. If no change, you or someone knowing what they are doing adjust
the high pressure side turnoff point of the regulator.

--
Noncompliant

Money don't wag the dog's tail.

>I left my garden hose from my well filling my new septic-tanks for the
> pump test. I needed to do this for the county inspector. My neighbor
> offered to shut the water off when one of the tanks(the one with the
> pump) reached 3/4 full(approx. 900 gals.) I left and he forgot so when
> I returned 2 days later both tanks were overflowing and the well pump
> was still running.
> Since then the pressure tank gauge in the well house never goes over
> 40 lbs. of pressure. It use to go up to 60 lbs. and then back down to
> 40 lbs. when water was running, then build up to 60 lbs. again when
> the water was not being used. The water pressure at the hose seems to
> be about the same as before this happened.
> Is it possible that the gauge or something else went haywire when that
> greater-than-usual demand was placed on the well?
> Any suggestions will be appreciated. Thanks, Jack
>



Similar ThreadsPosted
Pressure Washers March 14, 2007, 10:58 am
Water Well Pressure Tank September 10, 2006, 11:05 am
pressure treated studs August 24, 2007, 11:30 am
Pressure WRT Main Body November 28, 2007, 12:53 am
well water pressure loss over distance October 27, 2006, 5:43 pm
does the irc require pressure treated bottom plates on a slab on grade house? October 23, 2006, 4:50 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap