2 line oil line hook up.DOMESTIC.

Posted by lou on November 18, 2006, 9:53 pm

i would like to hook up my oil furnace.to my oil tank.it is now 1 line.
but i put the oil tank out
side,and now i have to hook up 2 line,because of concrete wall
height.is there a picture on a hook up for 2 line. i under stand at
tank.2 lines go to top of tank.1 line,suction goes 2" from botto
bottom.return line 2" from top.is this correct. problem i have is.if
suction line goes to oil pump. were 1 line suction went. were does the
return line on oil pump go.i assume you take out plug.do you remove a
part.pfg would help.THANKS.

Posted by on November 18, 2006, 10:46 pm

>i would like to hook up my oil furnace.to my oil tank.it is now 1 line.
>but i put the oil tank out
>side,and now i have to hook up 2 line,because of concrete wall
>height.is there a picture on a hook up for 2 line. i under stand at
>tank.2 lines go to top of tank.1 line,suction goes 2" from botto
>bottom.return line 2" from top.is this correct. problem i have is.if
>suction line goes to oil pump. were 1 line suction went. were does the
>return line on oil pump go.i assume you take out plug.do you remove a
>part.pfg would help.THANKS.

Ask dildo, sounds like you speak his language.

Posted by Stormin Mormon on November 19, 2006, 7:59 am

sounds.like.time.to.call.the.heating.guy.who.does.your.clean.and.chcek
s.
he.may.have.experience.with.this.kind.of.thing.WELCOME.

--

Christopher A. Young
You can't shout down a troll.
You have to starve them.
.

i would like to hook up my oil furnace.to my oil tank.it is now 1
line.
but i put the oil tank out
side,and now i have to hook up 2 line,because of concrete wall
height.is there a picture on a hook up for 2 line. i under stand at
tank.2 lines go to top of tank.1 line,suction goes 2" from botto
bottom.return line 2" from top.is this correct. problem i have is.if
suction line goes to oil pump. were 1 line suction went. were does the
return line on oil pump go.i assume you take out plug.do you remove a
part.pfg would help.THANKS.

Posted by geoman on November 20, 2006, 5:02 pm

The one side of the pump needs to be plugged, but the furnace has to be
adjusted to the new set up.
Not a DIY unless you have ALL the tools to test pressures, O, CO2, Spot
check etc etc.

>i would like to hook up my oil furnace.to my oil tank.it is now 1 line.
> but i put the oil tank out
> side,and now i have to hook up 2 line,because of concrete wall
> height.is there a picture on a hook up for 2 line. i under stand at
> tank.2 lines go to top of tank.1 line,suction goes 2" from botto
> bottom.return line 2" from top.is this correct. problem i have is.if
> suction line goes to oil pump. were 1 line suction went. were does the
> return line on oil pump go.i assume you take out plug.do you remove a
> part.pfg would help.THANKS.
>

Similar Threads	Posted
R22 TO 410: HAVE TO REPLACE LINE??	July 6, 2007, 8:46 am
R22 TO 410: HAVE TO REPLACE LINE?? again	July 6, 2007, 8:53 am
line set replacement help	May 31, 2007, 10:51 pm
Air in pex water line	March 18, 2009, 11:36 pm
Chimney line and flue	August 9, 2006, 4:30 pm
liquid line in condensate	June 27, 2007, 7:56 am
Re-use R22 line set for Puron system	November 4, 2006, 6:24 pm
water line air test	September 17, 2007, 8:19 pm
Air in Oil Feed Line to Furnace	December 15, 2007, 11:20 am
Primary AC Drain Line vent	July 28, 2006, 2:36 pm