If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on January 29, 2008, 12:54 am
The GE furnace is a model BLU055E936.
Problem: The blower motor hums and if I don't turn it off immediately,
it would burn up. I know this because this is the 3rd motor this
winter. The motor will get up to speed if you secure the service door
switch and wait for that moment when it just starts to hum and then
give it a push start with your hand. The blower motor won't come on
even when the fan is selected on the thermostat.
Attempted Fixes:
Everything electrical and mechanical has been replaced, which
includes:
Motor, Capacitor, Relay, Transformer, Limit Switch, Thermal Coupler,
Gas Valve, Fusible Link, Thermostat and all low voltage and hi voltage
wiring. All of the parts were ordered using the information on the
furnace. The wiring was rewired using a schematic for this unit. The
breakers and wiring where the power enters the house has be cleaned up
and new breakers installed.
We have even had an HVAC Technician come over and he was unable to
figure it out.
Is there anyone out there that can shed some light on a possible fix?
Thank you very much in advance.
|
|
Posted by on January 29, 2008, 1:06 am
On Mon, 28 Jan 2008 21:54:14 -0800 (PST), cinema.sasquatch@gmail.com
wrote:
>The GE furnace is a model BLU055E936.
>Problem: The blower motor hums and if I don't turn it off immediately,
>it would burn up. I know this because this is the 3rd motor this
>winter. The motor will get up to speed if you secure the service door
>switch and wait for that moment when it just starts to hum and then
>give it a push start with your hand. The blower motor won't come on
>even when the fan is selected on the thermostat.
>Attempted Fixes:
>Everything electrical and mechanical has been replaced, which
>includes:
>Motor, Capacitor, Relay, Transformer, Limit Switch, Thermal Coupler,
>Gas Valve, Fusible Link, Thermostat and all low voltage and hi voltage
>wiring. All of the parts were ordered using the information on the
>furnace. The wiring was rewired using a schematic for this unit. The
>breakers and wiring where the power enters the house has be cleaned up
>and new breakers installed.
>We have even had an HVAC Technician come over and he was unable to
>figure it out.
>Is there anyone out there that can shed some light on a possible fix?
>Thank you very much in advance.
Quit wasting your time you cheap Home Moaner and get a new furnace!!!!
--
Click here every day to feed an animal that needs you today !!!
http://www.theanimalrescuesite.com/
Paul ( pjm @ pobox . com ) - remove spaces to email me
'Some days, it's just not worth chewing through the restraints.'
'With sufficient thrust, pigs fly just fine.'
HVAC/R program for Palm PDA's
Free demo now available online http://pmilligan.net/palm/
|
|
Posted by Jeffrey Lebowski on January 29, 2008, 5:16 am
> The GE furnace is a model BLU055E936.
> Problem: The blower motor hums and if I don't turn it off immediately,
> it would burn up. I know this because this is the 3rd motor this
> winter. The motor will get up to speed if you secure the service door
> switch and wait for that moment when it just starts to hum and then
> give it a push start with your hand. The blower motor won't come on
> even when the fan is selected on the thermostat.
> Attempted Fixes:
> Everything electrical and mechanical has been replaced, which
> includes:
> Motor, Capacitor, Relay, Transformer, Limit Switch, Thermal Coupler,
> Gas Valve, Fusible Link, Thermostat and all low voltage and hi voltage
> wiring. All of the parts were ordered using the information on the
> furnace. The wiring was rewired using a schematic for this unit. The
> breakers and wiring where the power enters the house has be cleaned up
> and new breakers installed.
> We have even had an HVAC Technician come over and he was unable to
> figure it out.
> Is there anyone out there that can shed some light on a possible fix?
> Thank you very much in advance.
PSC cap wire needs to be connected opp of the motor common on the mains buss
terminal.
HTH
--
|
|
Posted by The Freon Cowboy on January 29, 2008, 6:13 am
could have replaced it with a modern more efficient model with warranty , for
all that youve spent on it
cinema.sasquatch@gmail.com wrote:
>The GE furnace is a model BLU055E936.
|
|
Posted by Bobb on January 29, 2008, 7:04 am
That's your third motor, and you replaced "everything electrical and
mechanical". You couldn't have used a competent service company, because 1)
they wouldn't have replaced all those parts, and 2) they would have had a
lot of them on their truck, and 3) no technician would rewire an entire
furnace because of a blower motor.
So you did all this work yourself, and THEN you called someone. If a
competent technician found out you did all that stuff, he's be wise to pack
up his tools and back out the door without touching it. He'd also be smart
to not charge you and give you nothing in writing saying he was ever there.
Way too much liability.
That furnace was made in 1979 or 80, and is about 65% efficient. Replace it
with a 90+ furnace installed by a reputable local company. That's the best
fix.
> The GE furnace is a model BLU055E936.
> Problem: The blower motor hums and if I don't turn it off immediately,
> it would burn up. I know this because this is the 3rd motor this
> winter. The motor will get up to speed if you secure the service door
> switch and wait for that moment when it just starts to hum and then
> give it a push start with your hand. The blower motor won't come on
> even when the fan is selected on the thermostat.
> Attempted Fixes:
> Everything electrical and mechanical has been replaced, which
> includes:
> Motor, Capacitor, Relay, Transformer, Limit Switch, Thermal Coupler,
> Gas Valve, Fusible Link, Thermostat and all low voltage and hi voltage
> wiring. All of the parts were ordered using the information on the
> furnace. The wiring was rewired using a schematic for this unit. The
> breakers and wiring where the power enters the house has be cleaned up
> and new breakers installed.
> We have even had an HVAC Technician come over and he was unable to
> figure it out.
> Is there anyone out there that can shed some light on a possible fix?
> Thank you very much in advance.
|
Page 1 of 2 1 2 > last >>
| Similar Threads | Posted | | Replacing oil fired burner with on-demand LP water heater in forced air system | October 20, 2007, 8:41 pm |
| Intertherm gas forced hot air furnace. | December 24, 2007, 12:14 pm |
| East Coast +92% efficient oil fired horizontal furnace/ preference? | November 16, 2007, 10:31 am |
| Best brand, model for forced air gas furnace? | January 24, 2007, 12:02 pm |
| Replacing Natural Gas Forced Air Furnace in New York | January 24, 2007, 10:23 pm |
| looking around - working in cav-vav system, I'm working for a vav boxes manufacturer - working at customer service | September 3, 2006, 10:21 am |
| U.S. National Oil Fired Boiler | October 1, 2007, 9:04 pm |
| Utica Dry Base Oil Fired Boiler | August 19, 2006, 12:10 am |
| Chimney liner for oil fired boiler | November 6, 2007, 12:03 am |
| Forced air heating problem | January 31, 2008, 7:23 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>Problem: The blower motor hums and if I don't turn it off immediately,
>it would burn up. I know this because this is the 3rd motor this
>winter. The motor will get up to speed if you secure the service door
>switch and wait for that moment when it just starts to hum and then
>give it a push start with your hand. The blower motor won't come on
>even when the fan is selected on the thermostat.
>Attempted Fixes:
>Everything electrical and mechanical has been replaced, which
>includes:
>Motor, Capacitor, Relay, Transformer, Limit Switch, Thermal Coupler,
>Gas Valve, Fusible Link, Thermostat and all low voltage and hi voltage
>wiring. All of the parts were ordered using the information on the
>furnace. The wiring was rewired using a schematic for this unit. The
>breakers and wiring where the power enters the house has be cleaned up
>and new breakers installed.
>We have even had an HVAC Technician come over and he was unable to
>figure it out.
>Is there anyone out there that can shed some light on a possible fix?
>Thank you very much in advance.