Home Page link

Residential Boiler Domestic Coil

HVAC Discussions - Heating, ventilation and air conditioning. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Residential Boiler Domestic Coil warrenshudson 10-19-2006
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by on October 19, 2006, 9:31 pm
I have a quick question. I have talked to several local hvac
companies, and I really need a second opinion. Have a 4400 sf brick
home, outside of detroit mi. There is a 1955 US Radiator 200,000 btu
hot water boiler in the basement now, 3 zones, 3 b/g circulators, and 6
relays (3 24v coil relays for the circs. and 3 110v relays for the
burner). The furnace was initially oil burning with a domestic
tankless coil in it. The boiler was switched to gas in the 1980s.
After the switch, an electric water heater was installed, and the
tankless coil was left disconnected from water. When that electric
water heater went, it was replaced with a normal gas unit. Now- The
question:
I want to re-use that tankless coil to heat water ONLY during the
winter and ONLY for half the house (kitchen, laundry- high temp.) Now I
dont mind opening and closing a few valves every spring/fall, but the
question is how do I have the HVAC co set up the aquastat. I assume,
that originally, the boiler had a triple aquastat which kept the boiler
"warm" year round. Now there is a single aquastat, acting as a "high
limit" set to i think 160 degrees. The burner and aquastat only get
power when a circulator/zone is active. Since i shut the boiler down
during the summer, do I want a triple aquastat installed, or should I
just feed the existing aquastat 24v 24/7 during the winter ? I know
that years back, the space heating operated on the high portion of the
aquastat, and the water heating operated on the low side, since it
represented such a small load, but since I have a large hot water
demand, can I just run the boiler at one temperature (160-180) Thanks a
lot, I appreciate the help. Also- when i have my hvac co come out and
replace the aquastat and hook up the plumbing, has anyone had good luck
with a particular brand of aquastat?


Posted by Steve Scott on October 19, 2006, 9:54 pm
Replace your boiler. The thing is an antique. Consider a modulating
condensing boiler with an indirect fired water heater. With what
you're paying in fuel now you'll pay for the investment in short
order.

On 19 Oct 2006 18:31:14 -0700, warrenshudson@gmail.com wrote:

>I have a quick question. I have talked to several local hvac
>companies, and I really need a second opinion. Have a 4400 sf brick
>home, outside of detroit mi. There is a 1955 US Radiator 200,000 btu
>hot water boiler in the basement now, 3 zones, 3 b/g circulators, and 6
>relays (3 24v coil relays for the circs. and 3 110v relays for the
>burner). The furnace was initially oil burning with a domestic
>tankless coil in it. The boiler was switched to gas in the 1980s.
>After the switch, an electric water heater was installed, and the
>tankless coil was left disconnected from water. When that electric
>water heater went, it was replaced with a normal gas unit. Now- The
>question:
>I want to re-use that tankless coil to heat water ONLY during the
>winter and ONLY for half the house (kitchen, laundry- high temp.) Now I
>dont mind opening and closing a few valves every spring/fall, but the
>question is how do I have the HVAC co set up the aquastat. I assume,
>that originally, the boiler had a triple aquastat which kept the boiler
>"warm" year round. Now there is a single aquastat, acting as a "high
>limit" set to i think 160 degrees. The burner and aquastat only get
>power when a circulator/zone is active. Since i shut the boiler down
>during the summer, do I want a triple aquastat installed, or should I
>just feed the existing aquastat 24v 24/7 during the winter ? I know
>that years back, the space heating operated on the high portion of the
>aquastat, and the water heating operated on the low side, since it
>represented such a small load, but since I have a large hot water
>demand, can I just run the boiler at one temperature (160-180) Thanks a
>lot, I appreciate the help. Also- when i have my hvac co come out and
>replace the aquastat and hook up the plumbing, has anyone had good luck
>with a particular brand of aquastat?


--
If a tree falls in the woods and kills
a mime, does anyone care?





Posted by on October 19, 2006, 9:59 pm
On 19 Oct 2006 18:31:14 -0700, warrenshudson@gmail.com wrote:

>I have a quick question. I have talked to several local hvac
>companies, and I really need a second opinion. Have a 4400 sf brick
>home, outside of detroit mi. There is a 1955 US Radiator 200,000 btu
>hot water boiler in the basement now, 3 zones, 3 b/g circulators, and 6
>relays (3 24v coil relays for the circs. and 3 110v relays for the
>burner). The furnace was initially oil burning with a domestic
>tankless coil in it. The boiler was switched to gas in the 1980s.
>After the switch, an electric water heater was installed, and the
>tankless coil was left disconnected from water. When that electric
>water heater went, it was replaced with a normal gas unit. Now- The
>question:
>I want to re-use that tankless coil to heat water ONLY during the
>winter and ONLY for half the house (kitchen, laundry- high temp.) Now I
>dont mind opening and closing a few valves every spring/fall, but the
>question is how do I have the HVAC co set up the aquastat. I assume,
>that originally, the boiler had a triple aquastat which kept the boiler
>"warm" year round. Now there is a single aquastat, acting as a "high
>limit" set to i think 160 degrees. The burner and aquastat only get
>power when a circulator/zone is active. Since i shut the boiler down
>during the summer, do I want a triple aquastat installed, or should I
>just feed the existing aquastat 24v 24/7 during the winter ? I know
>that years back, the space heating operated on the high portion of the
>aquastat, and the water heating operated on the low side, since it
>represented such a small load, but since I have a large hot water
>demand, can I just run the boiler at one temperature (160-180) Thanks a
>lot, I appreciate the help. Also- when i have my hvac co come out and
>replace the aquastat and hook up the plumbing, has anyone had good luck
>with a particular brand of aquastat?


Jesus H Christ! Nothing about your question was quick.

Similar ThreadsPosted
residential boiler doublng as pool heater? April 2, 2007, 9:38 am
Carrier Geothermal | Domestic Hot Water July 28, 2007, 5:59 pm
Any boiler OWNER save money after converting to a high efficiency boiler? August 6, 2006, 11:25 am
On-demand hot water heater for domestic and space heating... June 22, 2007, 1:13 am
2 line oil line hook up.DOMESTIC. November 18, 2006, 9:53 pm
Residential 4-Ton pricing May 14, 2007, 8:43 am
Just Sold Off My Residential August 6, 2007, 2:48 pm
Charging Residential Air Conditioning? Help July 22, 2006, 7:02 pm
"Boilers" Residential Heating Are They ON There Way Out ? October 21, 2006, 6:51 pm
residential duct design modifications August 28, 2006, 10:07 am

Contact Us | Privacy Policy

XML SitemapXML Sitemap