Home Page link

Finding studs

Home| Search | About
Login Password
Register Now! Lost Password?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Page 1 of 8       1 2 3 > last >> Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Finding studs Richard Evans 10-03-2008
| `--> Re: Finding studs alfred.sanford10-03-2008
---> Re: Finding studs David Nebenzahl10-03-2008
| |--> Re: Finding studs Blattus Slafaly10-04-2008
| ---> Re: Finding studs clare at snyder dot ontario do10-10-2008
|--> Re: Finding studs John Grabowski10-04-2008
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by Richard Evans on October 3, 2008, 12:12 pm


I've struggled with this for the last forty years.

I want to hang something on a drywall wall, and I want to use the
studs instead of drywall anchors. I have the damndest time finding the
studs reliably.

There's the time-honored and lo-tech method of tapping on the wall and
listening for different tones of hollow wall vs solid stud. So, I find
a stud that way, then measure 16" (or 24") on either side, tap there,
and hear a hollow sound. At that point, the process becomes random and
seldom 100% accurate.

I have several electronic detectors and their performance is spotty as
well. I can scan the same spot three or four times and get three or
four different hits over a space of about four inches, too wide to be
a single 2x2. (No, I'm not finding a doubled stud.)

The most reliable gadget I have is also the simplest: a small plastic
horseshoe with a magnetic pointer suspended between the open ends. You
move it over the wall until the pointer moves, at which time you know
you have detected a nail head and are on a stud. The problem with that
is that nail heads are a very small area of a wall and it takes a lot
of systematic scanning to find them.

I invariably end up approximating where I think the studs are, then
punching trial holes with an awl. This leaves me patching lots of
little trial holes when I'm done.

Any suggestions?

Posted by charlie on October 3, 2008, 12:22 pm



> I've struggled with this for the last forty years.
>
> I want to hang something on a drywall wall, and I want to use the
> studs instead of drywall anchors. I have the damndest time finding the
> studs reliably.
>
> There's the time-honored and lo-tech method of tapping on the wall and
> listening for different tones of hollow wall vs solid stud. So, I find
> a stud that way, then measure 16" (or 24") on either side, tap there,
> and hear a hollow sound. At that point, the process becomes random and
> seldom 100% accurate.
>
> I have several electronic detectors and their performance is spotty as
> well. I can scan the same spot three or four times and get three or
> four different hits over a space of about four inches, too wide to be
> a single 2x2. (No, I'm not finding a doubled stud.)
>
> The most reliable gadget I have is also the simplest: a small plastic
> horseshoe with a magnetic pointer suspended between the open ends. You
> move it over the wall until the pointer moves, at which time you know
> you have detected a nail head and are on a stud. The problem with that
> is that nail heads are a very small area of a wall and it takes a lot
> of systematic scanning to find them.
>
> I invariably end up approximating where I think the studs are, then
> punching trial holes with an awl. This leaves me patching lots of
> little trial holes when I'm done.
>
> Any suggestions?

get a bunch of small supermagnets. you can get them for about .10/each when
you buy in bulk (i use
http://www.forcefieldmagnets.com/catalog/product_info.php?cPath=23_37&products_id=37).
run a stack over where you think the stud is and they'll be attracted to the
drywall screws. put a small magnet over each screwhead. you'll see exactly
where the studs run.



Posted by Smitty Two on October 3, 2008, 12:31 pm



> I've struggled with this for the last forty years.
>
> I want to hang something on a drywall wall, and I want to use the
> studs instead of drywall anchors. I have the damndest time finding the
> studs reliably.
>
> There's the time-honored and lo-tech method of tapping on the wall and
> listening for different tones of hollow wall vs solid stud. So, I find
> a stud that way, then measure 16" (or 24") on either side, tap there,
> and hear a hollow sound. At that point, the process becomes random and
> seldom 100% accurate.
>
> I have several electronic detectors and their performance is spotty as
> well. I can scan the same spot three or four times and get three or
> four different hits over a space of about four inches, too wide to be
> a single 2x2. (No, I'm not finding a doubled stud.)
>
> The most reliable gadget I have is also the simplest: a small plastic
> horseshoe with a magnetic pointer suspended between the open ends. You
> move it over the wall until the pointer moves, at which time you know
> you have detected a nail head and are on a stud. The problem with that
> is that nail heads are a very small area of a wall and it takes a lot
> of systematic scanning to find them.
>
> I invariably end up approximating where I think the studs are, then
> punching trial holes with an awl. This leaves me patching lots of
> little trial holes when I'm done.
>
> Any suggestions?

The $20 wall density detector I got from Radio Shack 20 years ago works
very reliably in my hands. When I loan it out, it doesn't. Seems it all
comes down to reading, and following, the instructions. It's simple to
use, but easy to use wrong.

Posted by Reggie Dunlop on October 3, 2008, 1:35 pm


>
>> I've struggled with this for the last forty years.
>>
>> I want to hang something on a drywall wall, and I want to use the
>> studs instead of drywall anchors. I have the damndest time finding the
>> studs reliably.
>>
>> There's the time-honored and lo-tech method of tapping on the wall and
>> listening for different tones of hollow wall vs solid stud. So, I find
>> a stud that way, then measure 16" (or 24") on either side, tap there,
>> and hear a hollow sound. At that point, the process becomes random and
>> seldom 100% accurate.
>>
>> I have several electronic detectors and their performance is spotty as
>> well. I can scan the same spot three or four times and get three or
>> four different hits over a space of about four inches, too wide to be
>> a single 2x2. (No, I'm not finding a doubled stud.)
>>
>> The most reliable gadget I have is also the simplest: a small plastic
>> horseshoe with a magnetic pointer suspended between the open ends. You
>> move it over the wall until the pointer moves, at which time you know
>> you have detected a nail head and are on a stud. The problem with that
>> is that nail heads are a very small area of a wall and it takes a lot
>> of systematic scanning to find them.
>>
>> I invariably end up approximating where I think the studs are, then
>> punching trial holes with an awl. This leaves me patching lots of
>> little trial holes when I'm done.
>>
>> Any suggestions?
>
> The $20 wall density detector I got from Radio Shack 20 years ago works
> very reliably in my hands. When I loan it out, it doesn't. Seems it all
> comes down to reading, and following, the instructions. It's simple to
> use, but easy to use wrong.

Similar experience here. I've got a $20 one I got at Sears maybe 25 years
ago and it works fine for me...always finds the stud. My wife insists that
she can put on her Sarah Palin lipstick and has no trouble finding all the
studs she wants....



Posted by Perry Aynum on October 4, 2008, 4:05 pm



> Similar experience here. I've got a $20 one I got at Sears maybe 25 years
> ago and it works fine for me...always finds the stud. My wife insists that
> she can put on her Sarah Palin lipstick and has no trouble finding all the
> studs she wants....
>


You betcha!



Page 1 of 8       1 2 3 > last >>
Similar ThreadsPosted
Studs behind drywall October 27, 2006, 2:10 pm
Moving studs May 7, 2007, 8:03 pm
DWV pipe through studs June 12, 2008, 8:37 am
Tub surrounds directly to studs? September 13, 2006, 10:13 am
hang mirror on studs? January 6, 2007, 1:16 am
pressure treated studs August 24, 2007, 11:30 am
Hanging cabinets 24" OC studs December 10, 2007, 12:07 am
metal studs supporting a tv? March 5, 2008, 6:52 pm
Kitchen Cabinets, No Studs November 15, 2008, 5:17 pm
venting bath exhaust fan through 2x4 studs April 30, 2006, 8:03 am

Contact Us | Privacy Policy

XML SitemapXML Sitemap