Home Page link

Fisher Paykel power wouldn't turn on

Home| Search | About
Login Password
Register Now! Lost Password?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Fisher Paykel power wouldn't turn on tomkanpa 04-06-2008
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by tomkanpa on April 6, 2008, 1:06 pm
I did a load of wash, and then put in a second load. Pressed the power
button, NOTHING. Tried a few more times, still no power. I looked at
the trouble shooting section of the owner's manual. It stated to
unplug the machine and wait 60 seconds. I did this, pressed the Power
button and everything was fine.
My question is, what happened that prevented the power from coming on
and what did the act of unplugging/plugging do to remedy the problem?
Is this normal or a preview of an upcoming problem?

Posted by EXT on April 6, 2008, 3:46 pm
On-board computer crashed, needed re-booting by powering down and then
powering up.
Probably from a power line spike. This is a common problem and solution for
many electronics.

I had a van a number of years ago where the transmission computer would lock
into 2nd gear. Solution was to turn the engine off, wait a moment, then
start up again and all would be right. Eventually had the circuit board
replaced.

>I did a load of wash, and then put in a second load. Pressed the power
> button, NOTHING. Tried a few more times, still no power. I looked at
> the trouble shooting section of the owner's manual. It stated to
> unplug the machine and wait 60 seconds. I did this, pressed the Power
> button and everything was fine.
> My question is, what happened that prevented the power from coming on
> and what did the act of unplugging/plugging do to remedy the problem?
> Is this normal or a preview of an upcoming problem?



Posted by on April 6, 2008, 4:45 pm

>I did a load of wash, and then put in a second load. Pressed the power
>button, NOTHING. Tried a few more times, still no power. I looked at
>the trouble shooting section of the owner's manual. It stated to
>unplug the machine and wait 60 seconds. I did this, pressed the Power
>button and everything was fine.
>My question is, what happened that prevented the power from coming on
>and what did the act of unplugging/plugging do to remedy the problem?
>Is this normal or a preview of an upcoming problem?

Just about anything with a microprocessor in it can occasionally "lock up". Lots
of potential causes, the most likely being fluctuating power at the wall.

If anything, I would shut off the power to that cicuit, remove the outlet where
the washer is plugged in, and replace it with a new one. Only costs a couple
dollars at most, and outlets, especially in damp areas, can become corroded
inside.

Make sure you have a good solid ground connection (metal to metal) as well. Most
washers have a separate grouind wire that goes from the chassis to the home's
ground grid. That used to mean a cold water pipe, but that is no longer up to
code.



Similar ThreadsPosted
Fisher & Paykel: Washing Machine... October 13, 2005, 1:18 pm
Fisher Paykel washer and dryer owners here? February 21, 2006, 5:25 pm
heater problem with fisher-paykel refrigerator October 25, 2006, 11:58 pm
Fisher Paykel washer more reliable than Kenmore? February 19, 2007, 1:46 pm
Fisher and Paykel Ecosmart Washer Noise February 27, 2007, 10:40 pm
Users of Fisher & Paykel Double Dishdrawer March 21, 2007, 6:37 pm
Fisher Scientific Isotemp Refrigerator not working March 15, 2006, 1:37 pm
Deteriorated Power Line Coming into House from Power Meter October 23, 2007, 10:18 am
Question About "Temporary Power Taps" (Power Strips) April 15, 2008, 12:40 pm
TURN $6 INTO $60,000!!!!! December 18, 2005, 2:37 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap