If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by norminn@earthlink.net on October 8, 2009, 4:09 pm
JoeSpareBedroom wrote:
show/hide quoted text
>> JoeSpareBedroom wrote:
>>> My kid just called from college saying his roommate painted his window
>>> frames with Sherwin-Williams gloss latex, and 8 hours later, there are
>>> pretty large areas where the paint ran and forms drips (more like globs).
>>> It's at the thick goo stage right now. Should they let it dry until it
>>> hardens (if ever), and then razor blade it off & repaint the bad spots,
>>> or what? I've never had this problem, so I don't know what to tell them.
>> Cut it cleanly w/ a razor blade if can w/o smearing it too badly.
>> Otherwise, just wait a little longer and it will dry and can be cleaned up
>> then before it is terribly hard. A little scuff-sanding and all will be
>> well.
>>> I told them to use real paint, but they don't listen.
>> I sincerely doubt it was the paint; undoubtedly inexperienced painter.
>
>
> Probably some of both. If you've never compared Sherwin-Williams with brands
> like Devoe or Martin-Senour, you owe it to yourself to do so. The difference
> is quite remarkable.
>
>
Sherwin Williams? You don't mean Sears, do you? I used SW only once,
exterior alkyd semi for trim. It was beautiful - the quality is
apparent when it is applied and long after. The difference between
cheap and good paint, even during application, is remarkable. Brushes
out beautifully, levels....just very good stuff.
|
|
Posted by JoeSpareBedroom on October 8, 2009, 4:12 pm
show/hide quoted text
> JoeSpareBedroom wrote:
>>> JoeSpareBedroom wrote:
>>>> My kid just called from college saying his roommate painted his window
>>>> frames with Sherwin-Williams gloss latex, and 8 hours later, there are
>>>> pretty large areas where the paint ran and forms drips (more like
>>>> globs). It's at the thick goo stage right now. Should they let it dry
>>>> until it hardens (if ever), and then razor blade it off & repaint the
>>>> bad spots, or what? I've never had this problem, so I don't know what
>>>> to tell them.
>>> Cut it cleanly w/ a razor blade if can w/o smearing it too badly.
>>> Otherwise, just wait a little longer and it will dry and can be cleaned
>>> up then before it is terribly hard. A little scuff-sanding and all will
>>> be well.
>>>> I told them to use real paint, but they don't listen.
>>> I sincerely doubt it was the paint; undoubtedly inexperienced painter.
>> Probably some of both. If you've never compared Sherwin-Williams with
>> brands like Devoe or Martin-Senour, you owe it to yourself to do so. The
>> difference is quite remarkable.
> Sherwin Williams? You don't mean Sears, do you? I used SW only once,
> exterior alkyd semi for trim. It was beautiful - the quality is apparent
> when it is applied and long after. The difference between cheap and good
> paint, even during application, is remarkable. Brushes out beautifully,
> levels....just very good stuff.
I haven't handled the particular paint they're using. But they had it shaken
at the SW store, took it straight home and used it. They said it was about
as thick as canned gravy that had been warmed up. Devoe & Martin-Senour are
about 3 times thicker. You can practically ASK the paint to apply itself and
it will obey. I know this sounds like an exaggeration, but it's not much of
one. If you haven't used either of those two brands, you really don't know
what you're missing.
|
|
Posted by cshenk on October 8, 2009, 6:03 pm
show/hide quoted text
> JoeSpareBedroom wrote:
>> "dpb" wrote
>>>> My kid just called from college saying his roommate painted his window
>>>> frames with Sherwin-Williams gloss latex, and 8 hours later, there are
>>>> pretty large areas where the paint ran and forms drips (more like
>>>> globs).
>>> I sincerely doubt it was the paint; undoubtedly inexperienced painter.
>> Probably some of both. If you've never compared Sherwin-Williams with
>> brands like Devoe or Martin-Senour, you owe it to yourself to do so. The
>> difference is quite remarkable.
> Sherwin Williams? You don't mean Sears, do you? I used SW only once,
> exterior alkyd semi for trim. It was beautiful - the quality is apparent
> when it is applied and long after. The difference between cheap and good
> paint, even during application, is remarkable. Brushes out beautifully,
> levels....just very good stuff.
Same here. I've painted with it any a time and it's quite decent. If they
have 'runs' they had to use too much on the brush.
Amusing to me story. Room mate of mine many years ago tried to paint a
window frame. It had runs on it (old dried ones) so she tried to use too
much paint to fill them in! Yup, worse runs.
|
|
Posted by Roemax on October 8, 2009, 5:26 pm
O P is confused ,as Sherwin William's makes martin senour paint!!
maybe buying the best s w paint has not been experienced by O P
'a good craftsman doesn't blame his tools"
show/hide quoted text
>> JoeSpareBedroom wrote:
>>> My kid just called from college saying his roommate painted his window
>>> frames with Sherwin-Williams gloss latex, and 8 hours later, there are
>>> pretty large areas where the paint ran and forms drips (more like
>>> globs). It's at the thick goo stage right now. Should they let it dry
>>> until it hardens (if ever), and then razor blade it off & repaint the
>>> bad spots, or what? I've never had this problem, so I don't know what to
>>> tell them.
>> Cut it cleanly w/ a razor blade if can w/o smearing it too badly.
>> Otherwise, just wait a little longer and it will dry and can be cleaned
>> up then before it is terribly hard. A little scuff-sanding and all will
>> be well.
>>> I told them to use real paint, but they don't listen.
>> I sincerely doubt it was the paint; undoubtedly inexperienced painter.
> Probably some of both. If you've never compared Sherwin-Williams with
> brands like Devoe or Martin-Senour, you owe it to yourself to do so. The
> difference is quite remarkable.
>
|
|
Posted by Oren on October 8, 2009, 6:04 pm
>'a good craftsman doesn't blame his tools"
Unless he finds out his wife used a perfectly good paint brush.
"Sum Beach"!
|
Page 2 of 4 < 1 2 3 > last >>
| Similar Threads | Posted | | Latex Paint drips on door - How to get rid of? | September 10, 2005, 5:07 am |
| How to get rid of paint drips | January 25, 2006, 7:46 pm |
| Peel-A-Way Paint Remover For Latex Paint: Any Good ? | July 15, 2006, 7:36 pm |
| Paint sprayer & latex paint | May 25, 2006, 9:44 pm |
| How To Tell if Paint is Latex or Oil? | March 24, 2007, 7:25 am |
| About all that latex paint... | April 8, 2007, 4:21 pm |
| latex paint | May 13, 2007, 12:06 pm |
| Oil Over Latex Paint ? | March 28, 2008, 4:19 pm |
| Latex - Oil Paint Problem | September 7, 2005, 5:17 pm |
| Latex paint - how to get it off stone? | November 2, 2005, 2:18 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>>> My kid just called from college saying his roommate painted his window
>>> frames with Sherwin-Williams gloss latex, and 8 hours later, there are
>>> pretty large areas where the paint ran and forms drips (more like globs).
>>> It's at the thick goo stage right now. Should they let it dry until it
>>> hardens (if ever), and then razor blade it off & repaint the bad spots,
>>> or what? I've never had this problem, so I don't know what to tell them.
>> Cut it cleanly w/ a razor blade if can w/o smearing it too badly.
>> Otherwise, just wait a little longer and it will dry and can be cleaned up
>> then before it is terribly hard. A little scuff-sanding and all will be
>> well.
>>> I told them to use real paint, but they don't listen.
>> I sincerely doubt it was the paint; undoubtedly inexperienced painter.
>
>
> Probably some of both. If you've never compared Sherwin-Williams with brands
> like Devoe or Martin-Senour, you owe it to yourself to do so. The difference
> is quite remarkable.
>
>