Home Page link

Galvanized pipe, not sure what to do?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Page 1 of 3       1 2 3 > last >> Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Galvanized pipe, not sure what to do? jonyskids 10-10-2006
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by on October 10, 2006, 12:06 pm


I recently purchased my first home. We decided that we would under
take some upgrading. When we stared on the bathroom we where planning
on just repainting. After further investigation we determined that the
drain pipe from the sink was corroded and leaking. We didn't like the
sink anyway so we pulled it out and hope to replace it with a pedestal
sink. When we removed the sink this what we found.

http://www.eganllc.com/images/pipes1.jpg
http://www.eganllc.com/images/pipes2.jpg

The end of the pipe that you can not see is into a cast iron pipe.

As you can see there are many issues. 1) Do I need to replace the
galvanized pipe? 2) Should I call a plumber to do this? 3) Can I just
shorten the coupling so that the drain is not over the water pipe?
(Shorten the coupling that is.)

Any help is appreciated.

Jonyskids


Posted by on October 10, 2006, 12:37 pm


I'd base the course of action on whether that galvanized pipe is
obstructed. Does the sink drain rapidly ? Can you get a wire hanger
thru there ?

If it seems healthy I'd leave it alone. If it's a problem right now,
that is, water doesn't drain, it's probably because the galv. pipe is
corroded down to where only a trickle of water can pass.

I'm pretty handy but I'd call a plumber cause of the junction of that
pipe with what probably is an iron stack, assuming it's an old house.


Posted by on October 10, 2006, 12:42 pm


I would replace all the galvanized pipe. It's nothing but trouble.
Make it plastic all the way until you get to the cast iron pipe. May
as well do it now while the wall is open and you are redoing stuff
anyway. Galvinized pipe is a problem waiting to happen, espically on
water supply lines. I am not sure how bad it is on drain lines, but I
still wouldn't want it.


Posted by on October 10, 2006, 1:05 pm


The pipe drains fine although the angle is slightly the wrong
direction. If I choose not to replace, the issue is where the pipe
comes out of the wall. Need it to be at least 5 inched to the left.

roger61611@yahoo.com wrote:
> I'd base the course of action on whether that galvanized pipe is
> obstructed. Does the sink drain rapidly ? Can you get a wire hanger
> thru there ?
>
> If it seems healthy I'd leave it alone. If it's a problem right now,
> that is, water doesn't drain, it's probably because the galv. pipe is
> corroded down to where only a trickle of water can pass.
>
> I'm pretty handy but I'd call a plumber cause of the junction of that
> pipe with what probably is an iron stack, assuming it's an old house.


Posted by Heathcliff on October 10, 2006, 2:16 pm



jonyskids@gmail.com wrote:
> The pipe drains fine although the angle is slightly the wrong
> direction. If I choose not to replace, the issue is where the pipe
> comes out of the wall. Need it to be at least 5 inched to the left.
>
> roger61611@yahoo.com wrote:
> > I'd base the course of action on whether that galvanized pipe is
> > obstructed. Does the sink drain rapidly ? Can you get a wire hanger
> > thru there ?
> >
> > If it seems healthy I'd leave it alone. If it's a problem right now,
> > that is, water doesn't drain, it's probably because the galv. pipe is
> > corroded down to where only a trickle of water can pass.
> >
> > I'm pretty handy but I'd call a plumber cause of the junction of that
> > pipe with what probably is an iron stack, assuming it's an old house.

The PVC pipes and galvanized pipes are interchangeable in terms of
couplings -- in other words they use the same sizes and threads. So
yes you could take off the coupling and put a different one on,
although whether you could save 5 inches that way is hard to tell from
the photo. Sometimes you can get creative with drain pipes, loop it
around and so forth to get the geometry you need. Extra bends are not
good practice, of course, but as long as they don't clog up they won't
really hurt anything. Or you could take out the galvanized pipe,
replace it with PVC, and make everything nice and neat. How handy are
you and do you have the tools you need? One way to get comfortable
with the task is to go the hardware store, pick up some of the
couplings and play around with them, see how they go together, and what
different kinds there are. If you want to remove the galvanized pipe,
you will need a pipe wrench and perhaps a good amount of
strength/leverage to get it started. There is always some possibility
of disaster -- the pipe breaks or worse yet, breaks the cast iron stack
-- when dealing with old pipes. Personally I've had good luck though.
-- H


Page 1 of 3       1 2 3 > last >>
Similar ThreadsPosted
galvanized pipe for gas November 16, 2005, 9:30 pm
PEX to Galvanized Pipe November 10, 2006, 8:34 am
Galvanized Pipe December 21, 2006, 11:20 am
Black pipe or galvanized? July 1, 2005, 12:17 pm
rethreading Galvanized pipe December 22, 2006, 8:57 am
how to make new galvanized pipe look old February 15, 2007, 3:22 pm
Galvanized stell pipe January 21, 2008, 2:06 pm
Painting galvanized pipe ?? January 27, 2008, 1:06 pm
bending galvanized pipe July 15, 2008, 10:39 am
Rebuilt galvanized water pipe" November 16, 2005, 7:23 am

Contact Us | Privacy Policy

XML SitemapXML Sitemap