If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on August 20, 2008, 5:41 pm
I just had my hardwood floors refinished, and a single, short, curly
hair (about 3/4" long) must have fallen onto the floor prior to the
last coat of poly, and now it is beneath that coat of poly. It sort-
of catches the light when you walk in and out of the room, so it is
quite noticable.
Is there any way to remove the hair (which is just beneath the
surface) without damaging the finish? If not, is there any way to
hide the disturbance to the finish? (Maybe one of those floor
cleaning solutions with poly?)
Thanks.
|
 
| |
Posted by RicodJour on August 20, 2008, 6:28 pm
On Aug 20, 5:41=A0pm, gobofrag...@gmail.com wrote:
> I just had my hardwood floors refinished, and a single, short, curly
> hair (about 3/4" long) must have fallen onto the floor prior to the
> last coat of poly, and now it is beneath that coat of poly. =A0It sort-
> of catches the light when you walk in and out of the room, so it is
> quite noticable.
>
> Is there any way to remove the hair (which is just beneath the
> surface) without damaging the finish? =A0If not, is there any way to
> hide the disturbance to the finish? =A0(Maybe one of those floor
> cleaning solutions with poly?)
Nope and nope. Anything you do to remove it will probably make the
blemish even more noticeable. The "sort of catches the light"
problems might "sort of never be noticed by anyone else". If you do
decide to pick it out, be prepared to spot sand and add another coat
if it does become more objectionable. If you put down gloss poly and
the hair is in a trafficked area, the scuffs and scratches of every
day living will quickly make it less noticeable.
R
|
|
Posted by BRUCE on August 20, 2008, 6:48 pm
Easiest solution would be to sprinkle hairs all over the table and then
put on another coat of poly. Let em think it's the textured finish you
were going for.
|
|
Posted by Michael A. Ball on August 20, 2008, 8:03 pm
On Wed, 20 Aug 2008 15:28:06 -0700 (PDT), RicodJour
>On Aug 20, 5:41 pm, gobofrag...@gmail.com wrote:
>> I just had my hardwood floors refinished, and a single, short, curly
>> hair (about 3/4" long)...
Use and exacto knife to remove the hair. Buff that spot with a clean
clothe. Using the same product and a very tiny brush, build up the
crevice via as many coats as necessary. Once level, and cured, a little
buffing should make it tolerable; maybe flawless. Good luck.
________________________
Whatever it takes.
|
|
Posted by mm on August 20, 2008, 7:44 pm
On Wed, 20 Aug 2008 14:41:14 -0700 (PDT), gobofraggle@gmail.com wrote:
>I just had my hardwood floors refinished, and a single, short, curly
>hair (about 3/4" long) must have fallen onto the floor prior to the
>last coat of poly, and now it is beneath that coat of poly. It sort-
>of catches the light when you walk in and out of the room, so it is
>quite noticable.
>
>Is there any way to remove the hair (which is just beneath the
>surface) without damaging the finish? If not, is there any way to
>hide the disturbance to the finish? (Maybe one of those floor
>cleaning solutions with poly?)
What kind of poly is in that floor cleaning solution you have in
parens? Not polyurethane? I don't think there is any cleaning
solution that dissolves polyurethane and if there were, it would make
a lot of people angry when all they wanted to do was clean.
I hate to argue with a regular here, but my experience is that
patching polyurethane is not noticeable.
So I might just sand out the hair with medium to fine sand paper,
finishing with as fine as you used on the floor before you finished
it, and then patch with polyurethane.
I had a bad experience when I poly'd the dining room of the apartment
I rented. The instructions i read said to buff with steel wool between
coats, and how long to wait before buffing. I did, and the steel wool
embedded itself all over the floor. I'd returned the sanders and
didn't want to sand again anyhow, so I just put another coat on.
Later I noticed that unlike hardwood floors with other finishes IME,
the poly wore off in the areas of high traffic. I don't remembdr if
I patched those areas or not.
You could test my suggestion by taking a 1x2 foot piece of wood and
polying 2/3rds, sanding down part of it, and then repolying the sanded
part, blending in to the undsanded part. You'd be using the exact
same brand of poly, so it might be a very good test.
You know, you miight try prying one end up with a hat pin, and then
lifteing it all out. You can't pull it out lenthwise or that would
leave an empty tube yhou'd never be able to fill. You'd still have to
sand.
Or you could wait a while and see if you still notice it. Are you
intending to put another coat on soon?
>Thanks.
|
Page 1 of 2 1 2 > last >>
| Similar Threads | Posted | | DIY hair loss help | March 10, 2006, 10:55 pm |
| diy hair loss solutions | January 19, 2006, 5:15 am |
| How to get rid of Skin and Hair Problems at Home | August 27, 2006, 11:15 am |
| ashlee simpson hair styles | April 16, 2008, 5:15 am |
| Re: How To Get Laser Hair Removal Information | October 11, 2008, 10:44 am |
| Fiberglass shower tub with hair line crack | February 24, 2006, 5:45 am |
| How to protect your skin & hair to water infection | March 21, 2006, 1:01 am |
| Home improvement: Installing a hair dryer holder | March 11, 2006, 8:57 am |
| Polyurethane | September 20, 2007, 4:48 pm |
| Polyurethane over paint? | September 7, 2005, 4:10 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap