If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by marks542004 on September 25, 2006, 12:23 am
Eigenvector wrote:
show/hide quoted text
> I can't for the life of me think of the proper name for them, but when
> installing a new door, what is the best way to carve out the spaces for the
> hinges in the door?
> I've been using a hammer and chisel, it works but talk about hack work. I
> don't actually own a router, but is that the only real way to do it?
If your mortice looks hacked then you either have a bad tecnique or
need to sharpen that chisel.
I scribe the hinge outline with a very sharp exacto knife first.
|
|
Posted by scott21230 on September 25, 2006, 1:35 pm
I highly recommend using a router with a hinge template.
I am using:
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=33833
You'll only need the 1/4" bit from this set
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46396
A hinge template (use a metal one like this, not a plastic one): I got
mine off eBay
http://66.77.255.87/Images/VA%20Products/23457_VA/WEB_LG/23457_VA_lg.jpg
If you want to do the door latch part also, then you will need another
template for that:
http://images.orgill.com/200x200/6117337.JPG
This last item comes with a router bit that you will need to use with
the template so you don't destroy the plastic (which flexes, which is
why I hate it). I have never seen a metal one of these, but if you are
careful it works just fine.
Then take all these items and practice on some scrap wood until you get
it right. there are some good instructions available how to do this in
the internet (probably on hammerzone.com).
I have never and will never use a chisel to make a hing mortise. That
method sucks by comparison. And I didn't spend much to do it the right
way.
|
|
Posted by The Other Funk on September 25, 2006, 9:59 pm
Finding the keyboard operational
Eigenvector entered:
show/hide quoted text
> I can't for the life of me think of the proper name for them, but when
> installing a new door, what is the best way to carve out the spaces
> for the hinges in the door?
> I've been using a hammer and chisel, it works but talk about hack
> work. I don't actually own a router, but is that the only real way
> to do it?
Mortices were cut using hammer and chisels long before electricity was
harnessed. Make sure you have a sharp chisel and go slow. Small cuts are
better and easier to control then big ones.
Practice on some scrap first.
Bob
--
--
Coffee worth staying up for - NY Times
www.moondoggiecoffee.com
|
|
Posted by Phisherman on September 26, 2006, 7:03 am
On Sun, 24 Sep 2006 14:23:18 -0700, "Eigenvector"
show/hide quoted text
>I can't for the life of me think of the proper name for them, but when
>installing a new door, what is the best way to carve out the spaces for the
>hinges in the door?
Mortises. Either a chisel or router. A chisel takes more time (and
skill) than a router. If I have a lot of mortises to cut I build a
jig for the router.
show/hide quoted text
>I've been using a hammer and chisel, it works but talk about hack work. I
>don't actually own a router, but is that the only real way to do it?
|
|
Posted by Jim McLaughlin on September 26, 2006, 7:44 pm
Eigenvector wrote:
show/hide quoted text
> I can't for the life of me think of the proper name for them, but when
> installing a new door, what is the best way to carve out the spaces for the
> hinges in the door?
>
> I've been using a hammer and chisel, it works but talk about hack work. I
> don't actually own a router, but is that the only real way to do it?
>
>
oig some work a my son's place in VA last week I found a "kit" by (?)
Irwin (?) at a Lowes in Norfolk. Had the twmplates for the hinges and
a small bit with a rolling collar that could be powered by a cordless
drill. Son didn't have a router, but did have the drill. The drill
was an 18.something Sears Crapsman, but it worked for cutting 4 hinge
mortices and two striker plate mortices, one in the door jamb and one in
the door edge.
Whole thing worked out well.
|
Page 2 of 2 << first < 1 2
| Similar Threads | Posted | | Cabinet hinge | March 24, 2006, 8:10 pm |
| Maytag lid hinge | July 12, 2006, 2:32 am |
| Need help identifying hinge | November 25, 2007, 3:13 pm |
| Hinge Pin Locks | November 22, 2009, 3:52 pm |
| Installing a Hinge | March 5, 2010, 8:40 am |
| Hinge pin door stops | May 16, 2008, 5:27 pm |
| shimming door hinge | January 6, 2009, 2:16 pm |
| Tool for door hinge "insets"? | May 12, 2006, 9:57 pm |
| Needed - Unusual Cabinet Hinge | November 21, 2007, 9:32 pm |
| Toilet seat hinge question | August 7, 2008, 10:08 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> installing a new door, what is the best way to carve out the spaces for the
> hinges in the door?
> I've been using a hammer and chisel, it works but talk about hack work. I
> don't actually own a router, but is that the only real way to do it?