Home Page link

Home shower drip repair (how do I get the Delta faucet apart)?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Page 8 of 8       << first < 1 2 3 Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Home shower drip repair (how do I get the Delta faucet apart)? Donna 05-11-2008
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by Bob Thompson on May 14, 2008, 2:28 pm
> You cross post to four different groups, because you just love to share wi=
th
> a big audience, and you're always so polite and cheerful. It's really
> quite ugly.

I challenge Smitty Two to explain which are the four groups posted to
and how they do not relate to home repair by individuals presumably
wishing to save money over a plumber.
I also challenge Smitty Two to find where in the RFCs where it says
you're not supposed to cheerfully share your experiences with the
usenet audience?
Additionally, I challenge Smitty Two to find the answer to this
question as if it's already posted? Sure he'll find the question. But
I challenge him to find the answer. Until now.

Besides I only see three groups posted to and if I look at the first
reply tos it's only back to one group.

Smitty Two
What exactly is wrong with cheerfully sharing personal home repair
experiences in this group?

Posted by John Grabowski on May 13, 2008, 8:12 am

> On Mon, 12 May 2008 10:42:46 -0700 (PDT), Big_Jake wrote:
>> Good luck! That cartridge will likely set you back $30-$60. You
>> should probably be able to replace the two rubber "cups" for less than
>> a buck.
>
> Hi Big Jake,
> You were right on the money. On all counts! The Delta Monitor cartridge
> was
> $50 and the two rubber cups & springs under them were really all I needed
> to stop the leak.
>
> I tried both the new cartridge and the repair kit and, guess what, they
> both worked fine - so I returned the $50 cartridges and opted for just
> replacing the two rubber cups and springs below them. I also replaced the
> two small washers on the hot/cold water nipples on the cartridge, and the
> large O-ring on the outside of the cartridge.
>
> Overall, the job was easy once I removed the brass bonnet ring with a
> strap
> wrench! I did make a few mistakes though. For example, I turned on the
> water to test but I had forgotten to put the bonnet ring back on, and the
> cartridge shot out of the wall a quarter inch or so spewing water
> everywhere until I could shut off the main water supply.
>
> Also, the hot became cold and the cold became hot, so, I had to reverse
> the
> way I put the cartridge in the wall. But, overall, once that bonnet ring
> was off, it was a piece of cake. The bonnet ring is deceptive because it
> looks like it's part of the main brass assembly, whereas, in reality, the
> bonnet ring is in addition to the main brass assembly. That's what threw
> me
> off.
>
> To repeat, we did NOT have to take off the escutcheon. The only tools
> required to fix a leaking Delta Monitor single handle non tilt shower
> faucet were the 1/8 inch allen wrench to remove the grub screw holding the
> handle on and the strap wrench to remove the soft thin brass bonnet ring.
>
> I'll post some pics so the next person benefits from our work!
> Donna


Donna, thanks for getting back and letting us know the final outcome and for
the details of your experience. I wish more posters would come back with the
end result.


Posted by Donna on May 13, 2008, 8:49 am
On Tue, 13 May 2008 08:12:42 -0400, John Grabowski wrote:

> I wish more posters would come back with the end result.

Hi John,

Thanks for the kind words.

I very much thank you and Big_Jake, Joseph Meehan, Caloo Clay,
JoeSpareBedroom, hchickpea, and Gordon for your wonderful advice.

It's nice to know there's help out there when you need it!
And, now, there's the answer so the next person has the benefit of what
we've learned together!

Donna

Posted by Gordon on May 12, 2008, 8:53 pm
@nlpi070.nbdc.sbc.com:

> Well, I guess we know the answer. Spin out the bonnet. I am off to Ace to
> see if I can find a tiny strap wrench after work today. Wish me luck!
>
> Donna

In a pinch, I have used a leather belt for a strap wrench.

Posted by Donna on May 13, 2008, 1:44 am
On Tue, 13 May 2008 00:53:38 GMT, Gordon wrote:
> In a pinch, I have used a leather belt for a strap wrench.

Hi Gordon,
That would have worked, I'm sure, as with the strap wrench, the bonnet
easily spun off (I couldn't budge it without the strap though).
http://www.flickr.com/photos/donnaohl/2488962230/in/set-72157603940232052/

Here, so everyone benefits, are the additional photos showing the entire
repair (http://www.flickr.com/photos/donnaohl).

The Delta Monitor faucet repair slide show is here
http://www.flickr.com/photos/donnaohl/sets/72157603940232052/show/

I hope the next person with a leaky Delta Monitor single valve non-tilt
shower faucet can benefit from our discussion here.

Thanks everyone!
Donna

Page 8 of 8       << first < 1 2 3
Similar ThreadsPosted
Delta shower faucet repair December 15, 2006, 1:30 pm
Delta shower drip - one more question September 7, 2007, 11:55 am
delta shower faucet problem November 17, 2005, 6:39 pm
Help with dripping Delta shower faucet? July 5, 2005, 4:45 pm
Delta Monitor shower faucet?? January 13, 2008, 1:42 pm
Delta shower faucet, 2300 series January 12, 2008, 12:43 pm
Repair Delta Faucet August 30, 2005, 1:22 am
Shower head leak - drip...drip...drip... August 19, 2005, 12:51 am
Delta faucet screw November 19, 2005, 6:00 pm
Delta Faucet Question September 16, 2007, 1:22 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap