Home Page link

Load center and circuirt breaker questions

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Load center and circuirt breaker questions User Example 08-26-2005
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by User Example on August 26, 2005, 1:57 pm

> After the last one had me going, I can't wait to see how this one
> transpires..
> Searcher
>
The last one In retrospect dumping the salt OUT OF the bags into wheel
barrow ( clean) spreading around the pool with shovel might of been a better
idea, to bad I didn't think of that.



Posted by Bill on August 26, 2005, 7:24 am


It is more about what all you will have running at the *same* time. So you
may have a 20 amp circuit with a 5 amp appliance running and a 15 amp
circuit with a 1 amp something running, etc.

You may only be using a maximum of 20 amps say at *your* peak use times
when you have several things running at the same time. Just figure out what
the worst situation will be for running everything at the same time and if
that plus the A/C will be more than the loadcenter can provide max.

I like to use the Thanksgiving Day example; family and friends visiting:
Oven on, several burners on range going, all lights in house on, microwave
going, several TV's going, stereo in kids room going, video games in
another kids room going, hot water heater going, etc. The max use
situation.

The total amperage of all breakers typically will exceed the total amperage
of the panel. This is because you are not using the full amperage of every
single circuit at the same time. The breakers protect the wiring and
prevent the wiring from being overloaded. The main breaker to the panel
prevents the panel from being overloaded. People do not typically have
*everything* on at the same time.


"User Example" wrote in message
> I am adding an A/C to my garage and need to add a 240V circuit. The
> loadcenter is conveniently in my garage and has plenty of open spaces.
> However, I want to make sure I am not overloading it.
>
> What are the rules for adding circuit breakers? The label on the
> loadcenter says 120Amp max. but it already has 12 20Amp circuit breakers
> in it. 12X20 = 240Amps which is twice the rating. So, I am a bit
> confused.




Posted by SQLit on August 26, 2005, 9:01 am



> I am adding an A/C to my garage and need to add a 240V circuit. The
> loadcenter is conveniently in my garage and has plenty of open spaces.
> However, I want to make sure I am not overloading it.
>
> What are the rules for adding circuit breakers? The label on the
> loadcenter says 120Amp max. but it already has 12 20Amp circuit breakers
> in it. 12X20 = 240Amps which is twice the rating. So, I am a bit
> confused.

The max rating of the panel is nonsense unless the panel was fed with 125
amp wire. Check the wire feeding the panel and the breaker protecting the
wire...

Do a load calculation on the feeder to the panel including the new load. Ya
also may want to do a voltage drop calculation for the panel with the new
load connected.


http://www.electrician.com/vd_calculator.html





Similar ThreadsPosted
Load Center Bus Bar February 8, 2005, 9:45 pm
load center and branch wiring detail July 14, 2007, 1:07 pm
Replacing Flush Mount Zinsco Load Center, What will Fit? August 24, 2008, 11:38 am
Breakers compatible with Federal Pacific Stab-Lok Load Center April 16, 2008, 4:30 pm
Tub/shower faucet with 10" center to center October 2, 2005, 4:48 am
Measuring load on a circuit breaker. February 20, 2007, 3:30 pm
Measuring load on a circuit breaker. February 20, 2007, 3:30 pm
circuit breaker questions October 28, 2006, 1:53 pm
Refrigerator Center very very hot?? July 31, 2006, 4:50 pm
GARAGE DOOR STILL OFF CENTER !!! April 17, 2006, 11:16 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap