Mixer Tap

Posted by Murali Komakula on July 16, 2006, 8:04 pm

Hi,
Can anyone suggest Mixer Tap for me,
Basically, I am in a rented unit, so dont want to make any major
changes or buy expensive equipment.
I have a Vanity with Two taps, one for cold and one for hot. I would
like to use a single tap for this,
so basically i want something to mix these by connecting to the taps
and have a single tap, so i can get cold and hot together.
not able to find any in hardware shop, can anyone suggest?
thanks

Posted by No on July 17, 2006, 10:03 am

Murali Komakula wrote:
show/hide quoted text
This is what it sounds like you have
http://www.plumbingsupply.com/vintagebasinfaucets.html
It may depend on the spacing between your single taps. If its a standard
size and you have a middle hole you could just replace with a cheap new
faucet.
You may have a situation where you only have 2 holes in your sink. If
that is the case you may need to get more creative.
If one of these would fit it may work
http://www.plumbingsupply.com/lavfaucets3.html
Nothing exists, that I'm aware of, that will connect to your existing
faucets to allow them to blend into one spout.

Posted by mm on July 17, 2006, 1:02 pm

show/hide quoted text
You might be able to find it in a downtown hardware store, or a
hardware store in an old n'hood, if there are any left, that continue
to sell things specifically for old buildings. I KNOW there are still
many such places in NYC, but I don't know about any place else.
The building I lived in in college in the late 60's was probably from
the 30's, or late 40's. (Does anyone know when 5200 Woodlawn Ave. in
Chicago was built) maybe earlier than the 20's and it and thousands
and thousands of such units are still in Chicago and still in good
condition. I find it fairly hard to believe that most bathroom sinks
have been changed.
The problem I had is that in this particular building, the hot water
was almost scalding hot, so I wanted to mix it with cold, rather than
mix in IN the sink.
The hardware store in Hyde Park had these things that did so and
worked fine, chrome and adjustable as to width, with rubber seals to
go around the faucets where they entered. But it was expected by the
design that the taps be parallel. Since mine weren't, they toed in,
it kept falling off. The original two faucets were still there. This
was just a mixer, which is what you want, if I understood you
correctly.
So I just turned each of them a little, without using a basin wrench,
and without loosening the nut under the sink. (This meant that without
the mixer, the faucet wouldn't extend quite as far into the sink, but
that didn't bother me then.) Everything was fine for a couple weeks or
a month, when the line started leaking under the sink. It's an
interesting story how I kept damage from occurring, but it would have
been worse if I hadn't been home when it started.
show/hide quoted text

Similar Threads	Posted
Which Paint Mixer?	March 15, 2010, 2:57 pm
Small cement mixer?	August 9, 2005, 12:59 pm
50 year old cake mixer	August 24, 2005, 12:00 pm
Leaking Mono Mixer Tap	January 9, 2006, 6:42 am
Cement/mortar mixer	July 27, 2006, 8:45 pm
Concrete mixer, how to get a good mix?	June 4, 2007, 4:16 pm
Servicing Cement Mixer	August 4, 2007, 4:28 am
Old Shower Mixer Valve	September 18, 2008, 11:33 pm
Homemade concrete mixer	May 19, 2009, 4:48 pm
repairing a kitchenaid mixer	December 19, 2009, 3:10 pm