Home Page link

Rotten T-111 exterior paneling

Home| Search | About
Login Password
Register Now! Lost Password?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Rotten T-111 exterior paneling jthread 04-21-2007
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by jthread on April 21, 2007, 6:54 pm


Rotten T-111 exterior paneling



Hi guys:



I have a house in Austin TX with old exterior paneling (1980's). Most of it
I can repair with bondo except an area near the backdoor underneath and
awning.



Do you guys have any suggestions on how I could go about repairing this area
short of taking all the siding off and starting new?



http://www.safaricabs.com/t111rot.jpg



Here is another picture of the conduit that gets in the way and the window
ledge.



http://www.safaricabs.com/t111rot(2).jpg



I'd like to fix it as cheap as possible. The other side was repaired by
someone else like this:



http://www.safaricabs.com/t111fixed.jpg



This would be fine but I don't know exactly how they removed the old siding
and replaced it with the new.



Thanks



Jim.





PexSupply Save 50 468x60
Posted by Robert Allison on April 21, 2007, 10:16 pm


jthread wrote:
> Rotten T-111 exterior paneling
>
>
>
> Hi guys:
>
>
>
> I have a house in Austin TX with old exterior paneling (1980's). Most of it
> I can repair with bondo except an area near the backdoor underneath and
> awning.
>
>
>
> Do you guys have any suggestions on how I could go about repairing this area
> short of taking all the siding off and starting new?
>
>
>
> http://www.safaricabs.com/t111rot.jpg
>
>
>
> Here is another picture of the conduit that gets in the way and the window
> ledge.
>
>
>
> http://www.safaricabs.com/t111rot(2).jpg
>
>
>
> I'd like to fix it as cheap as possible. The other side was repaired by
> someone else like this:
>
>
>
> http://www.safaricabs.com/t111fixed.jpg
>
>
>
> This would be fine but I don't know exactly how they removed the old siding
> and replaced it with the new.


First of all, that is Reverse board and batten, not T-111.
Next, you could replace just a section of the panel that is
damaged. Cut it at the edge of the groove and just replace
the section that is damaged. Use Z flashing at the horizontal
junction of the old and new.


--
Robert Allison        
Rimshot, Inc.
Georgetown, TX

Posted by ythread on April 21, 2007, 10:56 pm



> jthread wrote:
>> Rotten T-111 exterior paneling
>>
>>
>>
>> Hi guys:
>>
>>
>>
>> I have a house in Austin TX with old exterior paneling (1980's). Most of
>> it I can repair with bondo except an area near the backdoor underneath
>> and awning.
>>
>>
>>
>> Do you guys have any suggestions on how I could go about repairing this
>> area short of taking all the siding off and starting new?
>>
>>
>>
>> http://www.safaricabs.com/t111rot.jpg
>>
>>
>>
>> Here is another picture of the conduit that gets in the way and the
>> window ledge.
>>
>>
>>
>> http://www.safaricabs.com/t111rot(2).jpg
>>
>>
>>
>> I'd like to fix it as cheap as possible. The other side was repaired by
>> someone else like this:
>>
>>
>>
>> http://www.safaricabs.com/t111fixed.jpg
>>
>>
>>
>> This would be fine but I don't know exactly how they removed the old
>> siding and replaced it with the new.
>
>
> First of all, that is Reverse board and batten, not T-111. Next, you could
> replace just a section of the panel that is damaged. Cut it at the edge
> of the groove and just replace the section that is damaged. Use Z
> flashing at the horizontal junction of the old and new.
>
>
> --
> Robert Allison Rimshot, Inc.
> Georgetown, TX

Thanks.



Posted by aemeijers on April 21, 2007, 10:33 pm



> Rotten T-111 exterior paneling
>
>
(snip)
>
> This would be fine but I don't know exactly how they removed the old
> siding and replaced it with the new.
>
It's just glorified plywood, and cheap enough that it isn't a major problem
if you screw up a couple of times till it looks right. The previous patch
work looks like they just sawed it off with a skilsaw, stuck some Z-flashing
up under the cut end, and scabbed in new panels. Shame on them for not
lining up the kerfs. Yes, the surface outlets and conduit will be a pain,
but if you undo the clamps and tug a bit, they will probably flex enough to
slide new wood behind them. You will have to pull the door trim, and
probably that outlet because of the ears. The rot occured because the bottom
edge probably wasn't sealed, and was jammed right against the concrete
foundation lip, rather than hanging over it Along with patching the siding,
you also wanna poke at the sill plate and joist ends to make sure they
didn't pick up any rot. Or is it a slab house? In that case, they F'd up by
not running a course of block to set the walls on. Walls should NEVER sit
right on the slab. I see no evidence of any flashing under the bottom of the
siding.

If the entire house has the siding jammed right down on the concrete like
that, as soon as you patch one spot, another will fail. Entire house needs
the bottom foot of siding cut off, proper flashing added, and then patch
back with a strip of hardiplank or something. That may or may not be cheaper
than a complete residing job, since piecing in requires better carpenter
skills than tearing off and replacing. Don't just side over it all- buried
rot keeps rotting.

aem sends....




Posted by ythread on April 21, 2007, 10:52 pm



>
>> Rotten T-111 exterior paneling
>>
>>
> (snip)
>>
>> This would be fine but I don't know exactly how they removed the old
>> siding and replaced it with the new.
>>
> It's just glorified plywood, and cheap enough that it isn't a major
> problem if you screw up a couple of times till it looks right. The
> previous patch work looks like they just sawed it off with a skilsaw,
> stuck some Z-flashing up under the cut end, and scabbed in new panels.
> Shame on them for not lining up the kerfs. Yes, the surface outlets and
> conduit will be a pain, but if you undo the clamps and tug a bit, they
> will probably flex enough to slide new wood behind them. You will have to
> pull the door trim, and probably that outlet because of the ears. The rot
> occured because the bottom edge probably wasn't sealed, and was jammed
> right against the concrete foundation lip, rather than hanging over it
> Along with patching the siding, you also wanna poke at the sill plate and
> joist ends to make sure they didn't pick up any rot. Or is it a slab
> house? In that case, they F'd up by not running a course of block to set
> the walls on. Walls should NEVER sit right on the slab. I see no evidence
> of any flashing under the bottom of the siding.
>
> If the entire house has the siding jammed right down on the concrete like
> that, as soon as you patch one spot, another will fail. Entire house needs
> the bottom foot of siding cut off, proper flashing added, and then patch
> back with a strip of hardiplank or something. That may or may not be
> cheaper than a complete residing job, since piecing in requires better
> carpenter skills than tearing off and replacing. Don't just side over it
> all- buried rot keeps rotting.
>
> aem sends....
>
That's too bad. It is a slab house (I think) It has a concrete foundation.

Thanks for the advice.



Similar ThreadsPosted
Repairing rotten exterior basement window sill November 24, 2005, 12:09 am
Painting pressure treated T111? August 6, 2006, 10:58 am
Rotten Egg, Tried Everything, What Next? August 8, 2005, 1:46 pm
Rotten floor near toilet August 15, 2006, 12:36 pm
Rotten Siding - Part 2 April 25, 2007, 9:18 pm
Replacing rotten load bearing 4 X 4 September 11, 2005, 8:39 pm
How to clean out rotten food in fridge October 16, 2005, 5:22 am
Basic repair of rotten wood February 11, 2008, 11:57 am
New tile smells like rotten fish August 23, 2008, 10:26 am
Paneling, has anyone done this??? January 23, 2007, 6:41 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap