|
Home Repair - - If it ain't broken, don't fix it. Otherwise look here.
|
|
|
|
If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Mikepier on October 13, 2007, 9:51 am
I'm getting ready to sheetrock my kitchen and was wondering if I
should sheetrock the entire wall or just sheetrock up to 36" high,
then put 18" high durock for the backsplash, then continue up with
sheetrock. Can I just rock the entire wall and still put the
backsplash tile on the sheetrock?
|
 
| |
Posted by EXT on October 13, 2007, 10:45 am
Durarock and other cement boards do not have a suitable paintable surface,
and is not really necessary unless you plan on having lots of water sloshing
around on your countertop. There are many ways to finish the backsplash that
will work better.
One hint that I learned the hard way, do not install nor let them install
drywall behind the cabinets with the standard seam 48" above the floor. This
is right in the middle of the backsplash and often where all the electrical,
phone and other outlets are located. Have them install a 2 foot strip along
the bottom of the wall, then a standard 4 foot wide sheet above it then
another 2 foot strip along the ceiling. This will place all the seams behind
the cabinets and leave the backsplash smooth.
The problem with a seam down the middle of the backsplash is tiles and other
rigid materials will not fit against the slight bulge of the seam causing
the tiles to rock or sit with one edge protruding above the tile below or
above it. When the tiles are cut around the electrical boxes small strips of
tile can be easily broken when fitting over the seam bulge. Placing the
seams behind the cabinets will provide a flat surface to fit whatever
backsplash material you want without placement problems.
> I'm getting ready to sheetrock my kitchen and was wondering if I
> should sheetrock the entire wall or just sheetrock up to 36" high,
> then put 18" high durock for the backsplash, then continue up with
> sheetrock. Can I just rock the entire wall and still put the
> backsplash tile on the sheetrock?
>
|
|
Posted by dadiOH on October 13, 2007, 11:56 am
Mikepier wrote:
> I'm getting ready to sheetrock my kitchen and was wondering if I
> should sheetrock the entire wall or just sheetrock up to 36" high,
> then put 18" high durock for the backsplash, then continue up with
> sheetrock. Can I just rock the entire wall and still put the
> backsplash tile on the sheetrock?
Yes.
--
dadiOH
____________________________
dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico
|
|
Posted by aemeijers on October 13, 2007, 4:06 pm
Mikepier wrote:
> I'm getting ready to sheetrock my kitchen and was wondering if I
> should sheetrock the entire wall or just sheetrock up to 36" high,
> then put 18" high durock for the backsplash, then continue up with
> sheetrock. Can I just rock the entire wall and still put the
> backsplash tile on the sheetrock?
>
Yeah, but durock near the sink and stove in the backsplash area would
be a good idea, since that is where the backsplash is likeliest to get
wet. The materials are pretty cheap, so your call as to if the
difference in labor is worth it. Personally, I'd use the durock the
whole backsplace area, and put the seams where the uppers and countertop
would hide them. That will give the flattest wall and most painless,
best looking tile job.
Don't forget, while you have the walls open, to add blocking at the top
rail level of the base cabinets, and at the upper and lower rail level
for the uppers. Not having to hunt for a stud when placing the cabinets
avoids a lot of cussing.
aem sends....
|
|
Posted by benick on October 13, 2007, 8:26 pm
> I'm getting ready to sheetrock my kitchen and was wondering if I
> should sheetrock the entire wall or just sheetrock up to 36" high,
> then put 18" high durock for the backsplash, then continue up with
> sheetrock. Can I just rock the entire wall and still put the
> backsplash tile on the sheetrock?
Yes,sheetrock the entire wall and as was stated earlier DO NOT PUT THE SEAM
IN THE MIDDLE. On just that wall put 2 seams above and below the cabinets.
Also on ALOT of kitchens I see the entire wall is done with 1/2 plywood then
drywalled to make cabinet installation ALOT easier...If you go that route
remember to move your outlet boxes out an extra 1/2 inch...Good luck with
your new kitchen.....
>
|
| Similar Threads | Posted | | Hardibacker for kitchen tile backsplash? | June 24, 2008, 4:33 pm |
| Choosing Beautiful Kitchen Backsplash Tiles | October 5, 2007, 5:33 am |
| travertine kitchen backsplash-mastic question | November 18, 2008, 8:48 pm |
| Replacing Kitchen Backsplash tiles, need to repair some damage | March 2, 2007, 9:25 am |
| Under the bathtub: Durock or just subfloor? | July 9, 2008, 4:15 pm |
| Durock meets Greenboard seams / what to mud with ? | March 16, 2008, 11:09 am |
| Thinset over mastic over durock seams in shower | August 6, 2007, 9:05 pm |
| Sheetrocking question | December 2, 2007, 4:38 pm |
| Embossed Backsplash | November 3, 2007, 11:43 am |
| How difficult to install a backsplash? | September 5, 2005, 8:43 am |
|
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap