Home Page link

Sliding patio door

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Sliding patio door tolbiny 10-16-2006
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by tolbiny on October 16, 2006, 6:52 pm


I have an exterior patio door on my home with 2 fixed glass panels and one
slider in the middle. I need to remove the doors. I am able to take the
middle slider out by lifting and tilting the door. The 2 fixed panels are a
problem. There are 2 screws on the top and bottom of each door that when
removed let the panel slide to the middle of the opening. However,the 2
screws screw into a block of wood that does not let me lift the door enough
to remove the panel from its track. I do not know the make of the doors. Can
anyone advise me how to remove the fixed panels from their tracks?



Posted by RLM on October 17, 2006, 1:30 pm


On Mon, 16 Oct 2006 18:52:18 -0400, tolbiny wrote:

> I have an exterior patio door on my home with 2 fixed glass panels and one
> slider in the middle. I need to remove the doors. I am able to take the
> middle slider out by lifting and tilting the door. The 2 fixed panels are a
> problem. There are 2 screws on the top and bottom of each door that when
> removed let the panel slide to the middle of the opening. However,the 2
> screws screw into a block of wood that does not let me lift the door enough
> to remove the panel from its track. I do not know the make of the doors. Can
> anyone advise me how to remove the fixed panels from their tracks?

Perhaps the reason that you were able to remove the center sliding door is
because it was not adjusted properly in the first place. Most sliding
glass doors have rollers at the bottom of the door that are adjusted by
screwing in a phillips screw that pushes the roller down and in turn lifts
the door high enough that it can *not* be lifted and removed without
lowering the door with the screw first. The adjusting screw is located
through a hole on the bottom edge of the door. This site has a number of
different styles of roller tensioners ("Sliding Door Roller Assembly") that
show the adjusting screw on the side(end). These roller assemblies are
underneath the bottom of each door panel.

http://hardware.hardwarestore.com/73-448-patio-door-rollers.aspx

My guess is that the side doors were installed properly and have not been
disturbed but the center door has had the rollers replaced at some time and
then not readjusted so the door was able to be lifted out due to improper
roller adjustment. Lowering the doors may enable you to remove the wood
blocks, allowing more clearance.

There are many different styles of the bottom rollers so look at the bottom
of the door you were able to remove for guidance.

Images of different styles
http://images.google.fr/images?hl=en&q=patio%20door%20roller&btnG=Google+Search&sa=N&tab=wi

Similar ThreadsPosted
Installing sliding Patio Door November 21, 2006, 10:03 am
Sliding patio door track April 23, 2007, 9:37 pm
Sliding patio door inside or outside? October 17, 2007, 8:48 pm
Sliding Patio Door Installation, etc., Costs July 16, 2005, 4:36 pm
Rough Opening For Sliding Patio Door November 21, 2006, 9:26 pm
Sliding patio screen door adjustment? July 27, 2008, 6:24 pm
replacement parts on sliding glass patio door May 6, 2007, 7:05 pm
Sliding patio door entry lock help needed May 20, 2007, 11:38 pm
Adding exterior lock on Andersen sliding patio door June 3, 2008, 1:07 pm
Patio Sliding Doors, Again June 11, 2007, 11:16 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap