Home Page link

Solid Surface Deck, Rebuilding and Coating

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Solid Surface Deck, Rebuilding and Coating Phil Anderson 07-14-2005
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by Phil Anderson on July 14, 2005, 9:59 am


Good Morning, All,

I have an elevated deck over my carport. The kitchen door and bedroom door
open onto the deck and we have patio furniture there for meals and
gatherings. Because the deck is over the carport, it has to be waterproof.
I also barbecue on the carport because with the protection of the deck, I
can do it year 'round. Well, the old plywood needs to be replaced due to
moisture damage. I have it all torn off and will be replacing it soon. I
also have to replace some of the framing for the deck, which is mostly 2x8's
on 16" centers. The deck is 20'x20' plus a four foot section that runs down
the length of the house to the bedroom door. That portion is 2x6's on 24"
centers. The old deck was caulked at the seams and just regular deck paint
applied. It lasted about 10 years.

The old deck had two layers of 3/4" ACX plywood on it, which I believe is
overkill. My plan is to use one layer of 3/4" ACX, facedown for appearance
below, and a top layer of 3/8" ACX crossband, if I can find it. Apparently,
it has a void free second layer so the furniture won't punch holes in it. I
will also apply 1x2" flashing around the outer edges of the deck, then new
railing.

Then, when it's ready, I want to apply a deck coating so the new surface
should last for years. I've looked at several products but can only
remember one brand, Gaco. Everything I have looked at is multi-coat,
usually requires taping the seams and is very expensive. While I hate to
spend the money ($1,000+) for the coating, it seems that is the way to go.

So, my questions are, does all of this seem like the correct way to proceed?
Does anyone have experience with Gaco or some other brand and can share the
experience/results? The house is located in Western Washington so we deal
with a lot of rain, very little snow, hardly ever gets below freezing
temperatures and seldom above 80-90 degrees. What do you think?

Best Regards, Phil

Living in the Woods of Beautiful Bonney Lake, Washington
Visit my Web site www.philsfun.com




PexSupply Save 50 468x60
Posted by on July 14, 2005, 10:28 am


I'd pay close attention to the railing. Getting it solidly anchored and
flashed can be difficult.
You don't mention flashing deck to the wall of the house and that is
important.

I had a deck done with Seal O Flex in October 004. Nice copper drip
edge. The material is tearing at the joints in the drip edge. Problem
has not been resolved, but I would guess movement in the drip allowed
it.

TB



Posted by Greg O on July 14, 2005, 5:49 pm



> Good Morning, All,
>
> I have an elevated deck over my carport. The kitchen door and bedroom
> door
> open onto the deck and we have patio furniture there for meals and
> gatherings. Because the deck is over the carport, it has to be
> waterproof.
> I also barbecue on the carport because with the protection of the deck, I
> can do it year 'round.

Probably not what you want to hear, but I would replace the rotting plywood,
have a roofing company put a rubber membrane over it, then put a "floating"
deck laid on the rubber. You could use 1X4 green lumber, with the decking of
your choice nailed to it. Build it in sections so you can remove the decking
to clean under it a couple times a year.
Greg




Similar ThreadsPosted
Solid Surface Countertops February 15, 2006, 7:00 am
Will solid color stan stick to a previously painted surface? April 15, 2006, 7:38 pm
Waterproof Deck Surface May 11, 2006, 3:50 pm
Exterior plywood for deck surface September 27, 2006, 9:52 pm
Sand in deck paint for non-skid surface? January 30, 2008, 7:59 pm
Deck surface boards, running opposite way?!! OK? October 27, 2008, 9:33 am
rebuilding old valves? December 10, 2007, 5:44 pm
Porch building, rebuilding September 13, 2005, 5:48 am
Rebuilding above ground pool, where to get parts? May 23, 2006, 2:44 pm
Rebuilding Cordless Drill Battery Pack September 6, 2005, 8:44 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap