Home Page link

Teak vanity top finish

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Page 1 of 2       1 2 > last >> Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
Teak vanity top finish ralft 08-03-2006
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by on August 3, 2006, 3:33 pm
I am concerned with what to use for a water impervious finish of a teak
wooden top for a bathroom vanity. A paint specialistt suggested a
marine varnish. Another suggestion is to go with polyurethane. Is that
the same thing? Also, I am aware of using automotive clear coat as an
ultimate finish protector.
Any suggestions?


Posted by JoeSpareBedroom on August 3, 2006, 4:11 pm
Post this in rec.boats. Seriously - you'll get real answers, and quickly.

>I am concerned with what to use for a water impervious finish of a teak
> wooden top for a bathroom vanity. A paint specialistt suggested a
> marine varnish. Another suggestion is to go with polyurethane. Is that
> the same thing? Also, I am aware of using automotive clear coat as an
> ultimate finish protector.
> Any suggestions?
>



Posted by JoeSpareBedroom on August 3, 2006, 4:12 pm
rec.woodworking, too.

>I am concerned with what to use for a water impervious finish of a teak
> wooden top for a bathroom vanity. A paint specialistt suggested a
> marine varnish. Another suggestion is to go with polyurethane. Is that
> the same thing? Also, I am aware of using automotive clear coat as an
> ultimate finish protector.
> Any suggestions?
>



Posted by pipedown on August 3, 2006, 11:48 pm
Marine spar varnish is a type of high quality polyurethane. I think what
makes it superior in wet locations is that it stays slightly soft and thus
is less likely to crack over time and allow water to get to the wood. it
also tends to leave a thicker coating and definitely cost more.

Teak is so dense, you could actually leave it unfinished or just oiled with
vegetable, linseed or teak oil (can leave a residual smell for a few weeks
after treating though) or other furniture oil applied regularly. Might
consider leaving it unfinished for a few months and if you change your mind,
you can just sand it and apply the varnish but you can't go the other way.


>I am concerned with what to use for a water impervious finish of a teak
> wooden top for a bathroom vanity. A paint specialistt suggested a
> marine varnish. Another suggestion is to go with polyurethane. Is that
> the same thing? Also, I am aware of using automotive clear coat as an
> ultimate finish protector.
> Any suggestions?
>



Posted by dadiOH on August 4, 2006, 8:38 am
pipedown wrote:
> Marine spar varnish is a type of high quality polyurethane.

I suppose that spar varnish made with polyurethane exists but it isn't
normal.

Spar varnish is made with more oil than normal so it dries softer and
more flexible because it is meant for spars. And spars bend.

The merit of polyurethane lies in its hardness. Hardness and
flexibility are mutually exclusive.

--

dadiOH
____________________________

dadiOH's dandies v3.06...
...a help file of info about MP3s, recording from
LP/cassette and tips & tricks on this and that.
Get it at http://mysite.verizon.net/xico




Page 1 of 2       1 2 > last >>
Similar ThreadsPosted
looking for tips on Teak repair/finish February 25, 2006, 5:42 pm
Teak Furniture by Westminster Teak May 3, 2008, 9:44 am
Teak Furniture April 5, 2008, 8:32 pm
What to use on exterior Teak furniture? June 9, 2007, 9:42 pm
Premium Teak Furniture by Smith & Hawken May 8, 2008, 6:12 am
To finish or not to finish the drywall November 12, 2006, 5:16 pm
Re: 48" vanity w/2 sinks April 16, 2006, 9:10 pm
Wood vanity top? August 1, 2006, 12:43 am
Re: To replace vanity top December 15, 2007, 6:00 pm
Re: To replace vanity top December 15, 2007, 5:54 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap