If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Robert11 on September 25, 2007, 12:20 pm
Hello,
For all youi electrical wizards out there:
Have a gas fired, forced hot water heating system.
Has 2 zones, circulator pump on each, and each with the very, very, basic
older Honeywell non-digital thermostat.
The old type, with the bimetallic spring and the mercury capsule.
Want to replace it with one of the new digital Honeywell.
The wiring from the existing thermostat to the furnace electrical circulator
control boxes is
2-wire. Pretty simple, basic system.
The wires are red and white.
But, the white wire seems to go to the red screw on each of the thermostats.
And, the red wire to the white screw.
I am calling it the red and white screw, as the wires that connects these
screws built into the thermostat that go to the bimetallic spring and heat
anticipator are led off of them with a red wire, and a white wire. No
molded in labeling, unfortunately.
Question:
For a system like this, 24 V AC, is this red-white wiring arbitrary, or
truly polarity sensative ?
Thanks,
Bob
|
|
Posted by bud-- on September 25, 2007, 1:06 pm
Robert11 wrote:
> Hello,
>
> For all youi electrical wizards out there:
>
> Have a gas fired, forced hot water heating system.
>
> Has 2 zones, circulator pump on each, and each with the very, very, basic
> older Honeywell non-digital thermostat.
> The old type, with the bimetallic spring and the mercury capsule.
>
> Want to replace it with one of the new digital Honeywell.
>
> The wiring from the existing thermostat to the furnace electrical circulator
> control boxes is
> 2-wire. Pretty simple, basic system.
>
> The wires are red and white.
> But, the white wire seems to go to the red screw on each of the thermostats.
> And, the red wire to the white screw.
>
> I am calling it the red and white screw, as the wires that connects these
> screws built into the thermostat that go to the bimetallic spring and heat
> anticipator are led off of them with a red wire, and a white wire. No
> molded in labeling, unfortunately.
>
> Question:
>
> For a system like this, 24 V AC, is this red-white wiring arbitrary, or
> truly polarity sensative ?
>
At your 2 wire thermostats it makes no difference at all.
By convention, red is the power source wire and white is the switched
wire that turns on the heat.
Some electronic thermostats operate on a battery which is charged (low
current) from the voltage across the thermostat contacts when the heat
is off.
--
bud--
|
|
Posted by on September 25, 2007, 5:49 pm
wrote:
>For a system like this, 24 V AC, is this red-white wiring arbitrary, or
>truly polarity sensative ?
Yes it is. but the main problem may be the new thermostat. what model
and brand did you buy?
|
|
Posted by hvacrmedic on September 25, 2007, 11:25 pm
> Hello,
>
> For all youi electrical wizards out there:
>
> Have a gas fired, forced hot water heating system.
>
> Has 2 zones, circulator pump on each, and each with the very, very, basic
> older Honeywell non-digital thermostat.
> The old type, with the bimetallic spring and the mercury capsule.
>
> Want to replace it with one of the new digital Honeywell.
>
> The wiring from the existing thermostat to the furnace electrical circulator
> control boxes is
> 2-wire. Pretty simple, basic system.
>
> The wires are red and white.
> But, the white wire seems to go to the red screw on each of the thermostats.
> And, the red wire to the white screw.
>
> I am calling it the red and white screw, as the wires that connects these
> screws built into the thermostat that go to the bimetallic spring and heat
> anticipator are led off of them with a red wire, and a white wire. No
> molded in labeling, unfortunately.
>
> Question:
>
> For a system like this, 24 V AC, is this red-white wiring arbitrary, or
> truly polarity sensative ?
>
> Thanks,
> Bob
With two wires the connections are arbitrary. Without a third wire to
the stat you'll need one that is battery operated if you go digital.
|
|
Posted by Robert11 on September 26, 2007, 7:50 am
Hi,
Thanks all for help; appreciate it.
The new digital Honeywell Thermostat I purchased is:
Model: RTH5100B (non programmable)
Runs on 2 AAA batteries internally.
Thanks,
Bob
----------------------------
> Hello,
>
> For all youi electrical wizards out there:
>
> Have a gas fired, forced hot water heating system.
>
> Has 2 zones, circulator pump on each, and each with the very, very, basic
> older Honeywell non-digital thermostat.
> The old type, with the bimetallic spring and the mercury capsule.
>
> Want to replace it with one of the new digital Honeywell.
>
> The wiring from the existing thermostat to the furnace electrical
> circulator control boxes is
> 2-wire. Pretty simple, basic system.
>
> The wires are red and white.
> But, the white wire seems to go to the red screw on each of the
> thermostats.
> And, the red wire to the white screw.
>
> I am calling it the red and white screw, as the wires that connects these
> screws built into the thermostat that go to the bimetallic spring and heat
> anticipator are led off of them with a red wire, and a white wire. No
> molded in labeling, unfortunately.
>
> Question:
>
> For a system like this, 24 V AC, is this red-white wiring arbitrary, or
> truly polarity sensative ?
>
> Thanks,
> Bob
>
|
| Similar Threads | Posted | | Thermostat question | February 7, 2005, 2:39 am |
| Thermostat question. | February 8, 2006, 6:33 pm |
| Thermostat Question | May 31, 2006, 10:06 pm |
| Thermostat question | February 1, 2007, 6:38 am |
| Thermostat question | October 23, 2007, 7:25 pm |
| Thermostat question | November 29, 2007, 7:13 pm |
| Thermostat question | August 21, 2008, 4:32 pm |
| Common question regarding thermostat | August 26, 2005, 11:08 pm |
| Gas dryer thermostat question. | May 31, 2006, 1:42 pm |
| Yet another digital thermostat question! | October 26, 2006, 10:56 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap