If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on June 17, 2007, 12:52 pm
I am having side steps installed via a city grant. The Bid and Scope
of work called for a composite; we ordered Trex because contractor
buys at HD.
Naive me thought composite was BETTER than wood. Turns out it is just
much cheaper!!!
Not to look "gift" steps in the mouth; they did replace dangerous old
concrete steps, but problems have arisen re: painting/staining.
Trex Website says need one kind of stain - semi-transparent -- for the
pressure-treated green wood that forms the supports on both sides and
the risers.
OK, fine.
Need another kind -- solid -- for the actual decking, or treads,and I
guess contractor is using it for handrails too (!) because of cost.
(How the hell much more could two short pieces of redwood cost??!!)
OK, fine.
But Trex Website says that their material has to "fade" for 12 to 16
weeks before it can be painted/stained with good results.
OK, fine.
Meantime, the treads are getting blotchy with water spots and
who knows what else.
Trex Website says to clean with "soap and water and a stiff brush".
I did, but it didn't clean up.
What to do? Just ignore the treads and any soiling until the "fading"
has taken place, THEN try to clean up before staining?
Or?
Your experience with composite decking/stair treads appreciated.
Aspasia
|
|
Posted by dpb on June 17, 2007, 1:30 pm
aspasia wrote:
> I am having side steps installed via a city grant. The Bid and Scope
> of work called for a composite; we ordered Trex because contractor
> buys at HD.
>
> Naive me thought composite was BETTER than wood. Turns out it is just
> much cheaper!!!
>
> Not to look "gift" steps in the mouth; they did replace dangerous old
> concrete steps, but problems have arisen re: painting/staining.
>
> Trex Website says need one kind of stain - semi-transparent -- for the
> pressure-treated green wood that forms the supports on both sides and
> the risers.
>
> OK, fine.
>
> Need another kind -- solid -- for the actual decking, or treads,and I
> guess contractor is using it for handrails too (!) because of cost.
> (How the hell much more could two short pieces of redwood cost??!!)
>
> OK, fine.
>
> But Trex Website says that their material has to "fade" for 12 to 16
> weeks before it can be painted/stained with good results.
>
> OK, fine.
>
> Meantime, the treads are getting blotchy with water spots and
> who knows what else.
>
> Trex Website says to clean with "soap and water and a stiff brush".
>
> I did, but it didn't clean up.
>
> What to do? Just ignore the treads and any soiling until the "fading"
> has taken place, THEN try to clean up before staining?
I certainly wouldn't do anything until then. Outdoors, "stuff" is going
to happen, whatever the material. Give it time, it will gradually get a
weathered look and blend in. I'm not sure I'd start the staining cycle,
but that's your call, I guess...
--
|
|
Posted by on June 17, 2007, 4:40 pm
I'd recommend TWP for the pressure treated parts of it (after it ages a
bit of course). Great stuff easy to work with..I think I learned of it
on this board..
|
|
Posted by on June 17, 2007, 7:43 pm
>aspasia wrote:
>> I am having side steps installed via a city grant. The Bid and Scope
>> of work called for a composite; we ordered Trex because contractor
>> buys at HD.
>>
>> Naive me thought composite was BETTER than wood. Turns out it is just
>> much cheaper!!!
>>
>> Not to look "gift" steps in the mouth; they did replace dangerous old
>> concrete steps, but problems have arisen re: painting/staining.
>>
>> Trex Website says need one kind of stain - semi-transparent -- for the
>> pressure-treated green wood that forms the supports on both sides and
>> the risers.
>>
>> OK, fine.
>>
>> Need another kind -- solid -- for the actual decking, or treads,and I
>> guess contractor is using it for handrails too (!) because of cost.
>> (How the hell much more could two short pieces of redwood cost??!!)
>>
>> OK, fine.
>>
>> But Trex Website says that their material has to "fade" for 12 to 16
>> weeks before it can be painted/stained with good results.
>>
>> OK, fine.
>>
>> Meantime, the treads are getting blotchy with water spots and
>> who knows what else.
>>
>> Trex Website says to clean with "soap and water and a stiff brush".
>>
>> I did, but it didn't clean up.
>>
>> What to do? Just ignore the treads and any soiling until the "fading"
>> has taken place, THEN try to clean up before staining?
>I certainly wouldn't do anything until then. Outdoors, "stuff" is going
>to happen, whatever the material. Give it time, it will gradually get a
>weathered look and blend in. I'm not sure I'd start the staining cycle,
>but that's your call, I guess...
You're quite right.
I'm not going to stain the treads unti the "fading" has happened.
The Trex Web site warns against precipitous action.
I will have the contractor stain the pressure-treated green wood
supports and risers -with a semi-transparent product, and leave me a
supply of matching solid stain for when it's time to do the treads.
Tx
Aspasia
|
|
Posted by Dan Espen on June 17, 2007, 10:38 pm
aspasia writes:
>>aspasia wrote:
>>> I am having side steps installed via a city grant. The Bid and Scope
>>> of work called for a composite; we ordered Trex because contractor
>>> buys at HD.
...
>>> But Trex Website says that their material has to "fade" for 12 to 16
>>> weeks before it can be painted/stained with good results.
That doesn't sound right. Here's what I found at the Trex site under
"painting":
Although Trex decking never needs to be painted or stained for
protection, be aware that you can paint or stain Trex products to
achieve a custom color.
Personally, I think putting paint or stain on composite is nuts.
|
Page 1 of 2 1 2 > last >>
| Similar Threads | Posted | | water stain in rug, how to clean? | June 19, 2007, 7:21 pm |
| How to clean a stain off a machine made or hand made rug | June 21, 2007, 1:42 pm |
| Which Trex is Best? | October 30, 2005, 10:05 pm |
| Trex Railing | November 20, 2007, 7:51 am |
| Question re: TREX | July 30, 2009, 10:03 pm |
| Decks--Anyone used Trex Brasilia? | July 3, 2005, 6:45 pm |
| Trex decking cleaner? | October 10, 2006, 5:23 pm |
| Trex vs. Ironwood prices | November 19, 2006, 1:59 pm |
| Trex - need to wait 12-16weeks? | July 9, 2007, 2:18 pm |
| Removing paint from TREX | August 31, 2007, 11:05 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> of work called for a composite; we ordered Trex because contractor
> buys at HD.
>
> Naive me thought composite was BETTER than wood. Turns out it is just
> much cheaper!!!
>
> Not to look "gift" steps in the mouth; they did replace dangerous old
> concrete steps, but problems have arisen re: painting/staining.
>
> Trex Website says need one kind of stain - semi-transparent -- for the
> pressure-treated green wood that forms the supports on both sides and
> the risers.
>
> OK, fine.
>
> Need another kind -- solid -- for the actual decking, or treads,and I
> guess contractor is using it for handrails too (!) because of cost.
> (How the hell much more could two short pieces of redwood cost??!!)
>
> OK, fine.
>
> But Trex Website says that their material has to "fade" for 12 to 16
> weeks before it can be painted/stained with good results.
>
> OK, fine.
>
> Meantime, the treads are getting blotchy with water spots and
> who knows what else.
>
> Trex Website says to clean with "soap and water and a stiff brush".
>
> I did, but it didn't clean up.
>
> What to do? Just ignore the treads and any soiling until the "fading"
> has taken place, THEN try to clean up before staining?