If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on September 21, 2006, 1:10 pm
Our whirlpool washer (direct drive) was making a whining noise, and
then quit altogether. I found that the motor coupling had broken, so I
replaced it. That worked, but it was still whining. I had not noticed
the whine before, but my wife (who does most of the laundry) said that
after the coupler replacement, it seemed to be louder. After a few
loads of clothes, she noticed water on the floor, so I pulled it
apart, and found that the pump had failed. It was real weird - it
looked like the plastic had melted, and there were these blobs of dark
colored melted plastic on the outside. So I figured, "hey, I guess two
things can go out at once", so I replaced the pump, and all seemed
well. The whine was gone, and the washer worked. My wife called this
morning to say it was whining again., but still working - so far.
Anyone have any idea what in the world might be going on here?
Everything seemed fine with the motor and such - all the parts came off
and went back together pretty easily, nothing seemed bent or broken or
otherwise amiss.
|
 
| |
Posted by Ether Jones on September 21, 2006, 7:08 pm
robert.macnutt@nghs.com wrote:
> Our whirlpool washer (direct drive) was making a whining noise, and
> then quit altogether. I found that the motor coupling had broken, so I
> replaced it. That worked, but it was still whining. I had not noticed
> the whine before, but my wife (who does most of the laundry) said that
> after the coupler replacement, it seemed to be louder. After a few
> loads of clothes, she noticed water on the floor, so I pulled it
> apart, and found that the pump had failed. It was real weird - it
> looked like the plastic had melted, and there were these blobs of dark
> colored melted plastic on the outside. So I figured, "hey, I guess two
> things can go out at once", so I replaced the pump, and all seemed
> well. The whine was gone, and the washer worked. My wife called this
> morning to say it was whining again., but still working - so far.
>
> Anyone have any idea what in the world might be going on here?
> Everything seemed fine with the motor and such - all the parts came off
> and went back together pretty easily, nothing seemed bent or broken or
> otherwise amiss.
I replaced the coupler and the water pump (twice) on mine. Never had
any "whine".
I hope you shopped around for the water pump. Prices vary
dramatically. The first time I replaced the pump I paid full retail
at the local appliance parts store. The second time I shopped the
internet and found it for half the price. The other day I saw a pile
of them, brand new in boxes, for 4 bucks each, at the local surplus
store. I picked up half a dozen. I figured if the pump went out
twice, it will go out again (I tend to keep my appliances - the dryer
is now 27 years old).
Did you notice that the new replacement coupler you bought looks
different from the original one? Or was the original so chewed up you
couldn't tell? They re-designed the coupler since the failure rate
was so high. Any Whirlpool washer owners reading this thread? Look
under your machine. If you see a pile of black rubber crumbs, your
coupler is self-destructing. It won't be long now...
|
|
Posted by on September 21, 2006, 10:02 pm
OP, you can see if the new pump you installed is giving you problems by
removing the attachment clips and swinging it aside, then put the
machine in spin. The basket will begin to rotate, but since the pump
is not attached to the motor, it will be silent. If the sound is gone,
the pump is the problem and you should replace it.
On the other hand, if the pump you installed is not correctly seated
with all 4 feet firmly against the motor, it can make some noise. To
seat is correctly, give it a whack with your hand, or just remove it
and install it again.
|
|
Posted by on September 25, 2006, 8:40 am
nospamtodd@yahoo.com wrote:
> OP, you can see if the new pump you installed is giving you problems by
> removing the attachment clips and swinging it aside, then put the
> machine in spin. The basket will begin to rotate, but since the pump
> is not attached to the motor, it will be silent. If the sound is gone,
> the pump is the problem and you should replace it.
>
> On the other hand, if the pump you installed is not correctly seated
> with all 4 feet firmly against the motor, it can make some noise. To
> seat is correctly, give it a whack with your hand, or just remove it
> and install it again.
It seemed to seat pretty firmly, but I'll certainly give that a try.
To the previous reply: I paid at the same local appliance parts store
where I've been buying parts for years. Their prices I've found have
always been reasonable, and they've been very helpful with advice in
the past, so I like giving them my business. There's only one other
parts store in town, and the few times I've checked with them, their
prices have been higher. Unfortunately, when you have laundry piling
up from a family of five, you don't have the luxury of waiting on
delivery of a part ordered on the Internet, or happening upon a good
price at an unlikely place.
|
|
Posted by Ether Jones on September 25, 2006, 11:50 am
robert.macnutt@nghs.com wrote:
> Unfortunately, when you have laundry piling
> up from a family of five, you don't have the luxury of waiting on
> delivery of a part ordered on the Internet
I hear you. Fortunately for us (also family of 5) the leak was small
enough that we could simply put a towel under the leak and wait for the
part ordered from internet to arrive. It was less than half the price
than if purchased locally.
There are many on-line applicance repair sites that not only sell
deeply discounted parts, but also offer excellent help for DIY'ers.
Their advice, I have found, is superior to what is available locally.
|
| Similar Threads | Posted | | My details on "no spin" Kenmore or Whirlpool "Motor Coupling" upgrades, and washer repair. | December 29, 2006, 3:39 pm |
| whirlpool washer motor coupler | September 21, 2006, 10:44 pm |
| Whirlpool cloths washer will not pump out | August 30, 2006, 8:20 am |
| Need help replacing/finding Whirlpool Clothes Washer pump. | August 31, 2008, 7:18 pm |
| GE Washer Woes: Motor, Transmission, or Pump? | October 17, 2005, 9:48 am |
| Whirlpool tub motor | December 10, 2006, 4:33 pm |
| Whirlpool gas dryer motor repair | January 11, 2008, 11:14 am |
| Whirlpool Washer? | September 3, 2006, 7:05 pm |
| whirlpool washer | January 25, 2007, 11:17 pm |
| Whirlpool washer | February 17, 2007, 3:14 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap