If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Tony Hwang on May 21, 2006, 10:06 pm
andrei_kho@hotmail.com wrote:
show/hide quoted text
> Greetings,
>
> I have three old plastic "bubble" skylights on my roof that I would
> like to replace with new Velux glass ones. The old skylights are
> curb-mounted and, since the interior size of the opening is 21.5 x 45
> 1/4 inches and the "hole" underneath the bubble itself seems a
> little bit bigger, I think the Velux FCM 2246 skylights will fit. The
> slope of the roof seems to be 45 degrees.
>
> The question is- what might be the labor cost for skylight replacement?
> ( the skylight itself+flushing kit is approximately $205 in Lowe's).
> Since I already have skylights, I do not think I need any interior
> finish or making /expanding openings in the roof.
>
> I also think that an average roofer could do this kind of job so I
> don't need any specialized contractors - is this true?
>
> Thanks in advance,
>
> Andrei K.
>
Hmmm,
If you're handy kinda guy, it could be DIY with proper preparation and
few days good weather.
|
|
Posted by Robert Gammon on May 22, 2006, 8:06 am
andrei_kho@hotmail.com wrote:
show/hide quoted text
> Greetings,
> I have three old plastic "bubble" skylights on my roof that I would
> like to replace with new Velux glass ones. The old skylights are
> curb-mounted and, since the interior size of the opening is 21.5 x 45
> 1/4 inches and the "hole" underneath the bubble itself seems a
> little bit bigger, I think the Velux FCM 2246 skylights will fit. The
> slope of the roof seems to be 45 degrees.
> The question is- what might be the labor cost for skylight replacement?
> ( the skylight itself+flushing kit is approximately $205 in Lowe's).
> Since I already have skylights, I do not think I need any interior
> finish or making /expanding openings in the roof.
> I also think that an average roofer could do this kind of job so I
> don't need any specialized contractors - is this true?
> Thanks in advance,
> Andrei K.
>
Replacement domes can be ordered for under $100 each, shaped exactly to
fit your existing hardware with new seals for the dome. All you need to
do is get on the roof, remove the screws/clamps that hold the dome to
the fixture, clean the sill, install new gaskets, drop the dome in
place, put the frame back on, and screw/clamp the frame to the box.
|
|
Posted by andrei_kho on May 22, 2006, 2:12 pm
If I could do skylight replacement by getting on the roof myself, I
would do it. Unfortunately, my roof has 45 degrees or so slope and I
can't even stay on it. I also don't have long ladder or any other
tools/devices roofers use.
Robert, if you are talking about replacement of the old plastic
skylights with the new PLASTIC ones, you probably did not read my
initial post. I would like to get rid of these awful plastic bubbles
altogether and replace them with glass skylights. I hate bubbles and
think that they were invented by an enemy of (home owning) mankind-
they provide little or no thermal and noise insulation and looks ugly
after several years of use, as mine are. Looks like the only people who
love them are builders because plastic skylights are the cheapest.
By the way, I got a quota $550 for the whole replacement process,
including the cost of Velux skylight and flushing kit. Is this good?
Andrei
Robert Gammon wrote:
show/hide quoted text
> andrei_kho@hotmail.com wrote:
> > Greetings,
> > I have three old plastic "bubble" skylights on my roof that I would
> > like to replace with new Velux glass ones. The old skylights are
> > curb-mounted and, since the interior size of the opening is 21.5 x 45
> > 1/4 inches and the "hole" underneath the bubble itself seems a
> > little bit bigger, I think the Velux FCM 2246 skylights will fit. The
> > slope of the roof seems to be 45 degrees.
> > The question is- what might be the labor cost for skylight replacement?
> > ( the skylight itself+flushing kit is approximately $205 in Lowe's).
> > Since I already have skylights, I do not think I need any interior
> > finish or making /expanding openings in the roof.
> > I also think that an average roofer could do this kind of job so I
> > don't need any specialized contractors - is this true?
> > Thanks in advance,
> > Andrei K.
> Replacement domes can be ordered for under $100 each, shaped exactly to
> fit your existing hardware with new seals for the dome. All you need to
> do is get on the roof, remove the screws/clamps that hold the dome to
> the fixture, clean the sill, install new gaskets, drop the dome in
> place, put the frame back on, and screw/clamp the frame to the box.
|
Page 2 of 2 << first < 1 2
| Similar Threads | Posted | | skylight question - cost? Tips on spec'ing the job? | October 28, 2005, 8:26 pm |
| Cost of deck replacement | May 15, 2007, 4:50 pm |
| Cost for Installing Replacement Windows? | October 27, 2005, 6:44 pm |
| New A/C: Help with determining fair replacement cost | January 19, 2006, 3:27 pm |
| Wood replacement window cost? | June 3, 2006, 5:57 pm |
| Cedar Siding Replacement Cost | July 16, 2006, 1:54 pm |
| Attic Exhaust Fan replacement cost | July 28, 2006, 3:07 pm |
| Can anyone estimate a replacement cost for this residential garage? | May 27, 2006, 8:52 am |
| Ball park cost for breaker box replacement | September 15, 2006, 7:47 pm |
| Lifespan and replacement cost of galvanized pipe? | April 8, 2007, 9:50 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>
> I have three old plastic "bubble" skylights on my roof that I would
> like to replace with new Velux glass ones. The old skylights are
> curb-mounted and, since the interior size of the opening is 21.5 x 45
> 1/4 inches and the "hole" underneath the bubble itself seems a
> little bit bigger, I think the Velux FCM 2246 skylights will fit. The
> slope of the roof seems to be 45 degrees.
>
> The question is- what might be the labor cost for skylight replacement?
> ( the skylight itself+flushing kit is approximately $205 in Lowe's).
> Since I already have skylights, I do not think I need any interior
> finish or making /expanding openings in the roof.
>
> I also think that an average roofer could do this kind of job so I
> don't need any specialized contractors - is this true?
>
> Thanks in advance,
>
> Andrei K.
>