If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by James Toomey on September 28, 2006, 5:53 pm
We have a standard 30-gallon water heater on the outside of our house,
which used to have a metal enclosure around it. When we got the house
restuccoed, we removed the enclosure, which twisted and bent so badly
that we gave the metal to the recycling center. Now that we're ready
for a new enclosure, I'm finding that none will fit. The old enclosure
was 24d"x24"w, which is a standard size, but it was a whopping 91" tall
because the pipes extend way up the wall before entering the house. The
standard-sized enclosures are only about 60" tall. Does anyone have
ideas about what to do?
The plumbing supply house tells me not to build it from wood because
that's not up to code (fire hazard). I'm sure that having one
custom-fabricated would cost a lot. It seems like my only options are:
1) Custom-build one with sheet metal (and try to avoid lacerating my
hands).
2) Build a 2-foot footing, then plop a standard-sized enclosure on top
of that.
3) Drill new, lower holes through the stucco and have the pipes
re-routed through those holes (and patch the old holes, which will
never match the brand-new stucco).
4) Use a standard-sized enclosure and just let the pipes be exposed to
the outside.
|
|
Posted by Eric in North TX on September 28, 2006, 10:16 pm
A couple of thoughts;
R-panel oversize at 36" but readily available and fireproof especially
with a C-perlin frame, and it can all be assembled with self-tapping
screws with a drill.
http://www.ctmrs.com/panels/rpanel.shtml
Hardiboard concrete siding and structural boards, that can be cut to
size & again are fire proof.
http://www.jameshardie.com/homeowner/prodhome/default.php
|
|
Posted by Joe on September 28, 2006, 10:30 pm
James Toomey wrote:
> We have a standard 30-gallon water heater on the outside of our house,
> which used to have a metal enclosure around it.
<snip>
> 2) Build a 2-foot footing, then plop a standard-sized enclosure on top
> of that.
Probably cheapest and easiest if the enclosure is an off the shelf
item. It would look rather neat if the height extending masonry were
some nce stone or brick layup. HTH
Joe
|
|
Posted by Goedjn on September 29, 2006, 11:53 am
>James Toomey wrote:
>> We have a standard 30-gallon water heater on the outside of our house,
>> which used to have a metal enclosure around it.
>> 2) Build a 2-foot footing, then plop a standard-sized enclosure on top
>> of that.
>Probably cheapest and easiest if the enclosure is an off the shelf
>item. It would look rather neat if the height extending masonry were
>some nce stone or brick layup. HTH
USe the standard enclosdure, and insulate the pipes separately.
|
| Similar Threads | Posted | | Waterheater rod | October 30, 2006, 9:42 pm |
| tankless waterheater | April 14, 2007, 9:25 am |
| Waterheater death in 3 year old condo building | May 22, 2006, 2:11 pm |
| How tall a ladder? | September 9, 2005, 8:01 pm |
| How tall should outdoor antenna be? | October 25, 2007, 5:27 pm |
| tall storage cabinet | November 25, 2008, 12:57 pm |
| "Tall" Water Heaters are not taller? | October 8, 2007, 3:49 pm |
| Tall Deck Construction Question | December 3, 2007, 8:20 am |
| Cleaning tall metal chimney from downstairs? | August 22, 2005, 10:16 am |
| Scaffolds, ladders, painting a tall foyer | October 8, 2005, 8:34 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> which used to have a metal enclosure around it.