Home Page link

installing a bathroom exhaust vent through brick facade

Home| Search | About
Login Password
Register Now! Lost Password?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
installing a bathroom exhaust vent through brick facade Chris Jung 07-20-2005
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by Chris Jung on July 20, 2005, 10:11 am


Hi,
First a little background: Our house, a raised ranch, was built in 1967 and
the developer of this area was well known for cheapness and taking a lot of
short cuts. The only good part is that all the owners are in the same boat
and, as we share stories of remodeling surprises, it builds a bit of
neighborhood camaraderie.

We want to do a minor remodel of our downstairs bathroom, mainly the bath
surround and exhaust. The surround was put on regular drywall which wasn't
a good idea as in the past decades the drywall has been breaking down. You
can press on the surround and the wall behind it is soft. We want the
drywall replaced with waterproof board (greenboard right?) and a new
surround put in. Now the current bathroom ceiling exhaust set-up is
incredibly dumb - the duct work runs 5 feet in the ceiling (toward the
middle of the house) and then stops. It doesn't exhaust anywhere but in the
floor joists (you should have seen the open mouthed, WTF faces when we
figured that out). The exhaust fan is about 4 feet from an exterior wall
that has a brick facade. One of our neighbors told us that we will have to
run ductwork from the exhaust to the wooden facade side of the house (about
15 feet) since, in his opinion, it's too difficult to go through brick. I'm
not too keen on that for many reasons. We would have to run the ductwork
under the ceiling (unless we wanted to open up the drywall ceiling and cut
into the joists since the direction of the duct is perpendicular to the
joists) cutting through two interior walls, building drywall boxes around
the ductwork and my gut feeling is that having a 15 foot horozontal duct is
inefficient and perhaps hard on the exhaust fan motor.

Next week we are having a two recommended bathroom remodeling contractors
come and look at this. I, however, want to gather as much information as I
can beforehand. The brick and mortar is in excellent shape (we raise a
toast to that long ago worker who did competent work despite the developer's
urging to slap it together). Since this is a raised ranch, the exhaust vent
would come out at about 4 feet above ground. So how hard is it to cut a
rectangular opening through brick facade? Would installing an exhaust vent
through brick be huge, medium or no problem at all for a competent
carpenter? Does this require some sort of special worker/tool and is it
unsually expensive? Is there risk of causing damage to the surrounding
brick?

Thanks in advance for all advice and commentary.

Chris in hot yet still lovely Ithaca, NY




Posted by on July 20, 2005, 4:05 am


I don't think you need worry about the small hole in the brick.
A competent mason or general contractor should be able to remove the
few brick required for the vent.
Check the duct size against the brick wall, and you'll see how few
ricks need to come out.
I would think you want to make sure the wall behind the brick is well
sealed.
Bricks and joints in brickwork are not water tight.

I'll bet you can hardly wait for the snow.

TB



Posted by Chris Jung on July 21, 2005, 9:51 am



>I don't think you need worry about the small hole in the brick.
> A competent mason or general contractor should be able to remove the
> few brick required for the vent.
> Check the duct size against the brick wall, and you'll see how few
> ricks need to come out.
> I would think you want to make sure the wall behind the brick is well
> sealed.
> Bricks and joints in brickwork are not water tight.
>
> I'll bet you can hardly wait for the snow.
>
Hi TB,
Thanks for the comments. I figured that putting a vent through brick might
be tricky but not impossible if you know what you're doing. How does one
check if the wall behind brick is well sealed? I suspect it's OK. We owned
a "rubble built" two story limestone house in Pittsburgh and from that
experience I learned a little bit about the signs of stone & mortar trouble.
The brick & mortar on this house look good and I've never seen any
indication of water infiltration inside or out.

A high pressure front came through and the humidity dropped. The haze is
gone and the skies are clear and crisp. I don't mind temps in the 80s now.
I showshoe and my SO cross-country skis (did the Canadian Ski Marathon last
year) so yes, we can't wait for the snow.

Chris in lovely Ithaca, NY





Similar ThreadsPosted
Installing a bathroom exhaust fan and the proper way to vent it... November 11, 2005, 2:19 pm
Installing new bathroom exhaust fan March 14, 2008, 1:25 am
Installing two bathroom exhaust fans August 14, 2005, 9:13 pm
Installing a New Bathroom Exhaust Fan Question. January 25, 2008, 11:31 pm
Special roof vent for bathroom fan exhaust? September 29, 2006, 5:07 pm
How to remove a brick facade from a tile fireplace? April 29, 2007, 9:58 pm
Bathroom vent line hole in brick wall? May 29, 2006, 11:18 am
Dryer exhaust and bathroom exhaust distances May 19, 2008, 8:57 am
Installing an exhaust fan November 28, 2007, 10:26 pm
Installing bath exhaust fan June 1, 2008, 10:17 pm

Contact Us | Privacy Policy

XML SitemapXML Sitemap