If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by jw 1111 on March 28, 2006, 7:52 am
Hi, am putting some new magnetic catches on to all my kitchen cupboard
doors. ( the original spring type self-closing hinges are mostly very
tired ).
Since the door is actually shut when they are pressed together, you cannot
just line them up by sight. Is there any trick for getting the metal plate
lined up 'exactly' opposite the magnet catch?
|
|
Posted by RayV on March 28, 2006, 8:08 am
Screw one or the other in place (usually the magnet) put them together
and put chalk or lipstick on the back. Close and reopen the door and
you will see where to screw it in.
|
|
Posted by Newfie on March 28, 2006, 8:26 am
Most metal plates have a sticky backing, if your does not, add some hot
glue. Install the magnetic catch, place the plate on the magnet and
close the door - press it firmly for a few seconds. Open the door and
your plate will be in position on your door - screw the plate into
place.
jw 1111 wrote:
> Hi, am putting some new magnetic catches on to all my kitchen cupboard
> doors. ( the original spring type self-closing hinges are mostly very
> tired ).
> Since the door is actually shut when they are pressed together, you cannot
> just line them up by sight. Is there any trick for getting the metal plate
> lined up 'exactly' opposite the magnet catch?
|
|
Posted by John on March 28, 2006, 12:21 pm
> Most metal plates have a sticky backing, if your does not, add some hot
> glue. Install the magnetic catch, place the plate on the magnet and
> close the door - press it firmly for a few seconds. Open the door and
> your plate will be in position on your door - screw the plate into
> place.
Usually the plate has a 'pip' on the side that goes against the door inner
face. Screw the magnet to the cupboard, put the plate on the magnet, pip
out. Shut the door and press it into the magnet. Open the door and there
should be a small mark on the back of the door where the pip goes, screw
plate to door.
HTH
John
|
|
Posted by L. M. Rappaport on March 28, 2006, 9:29 am
On Tue, 28 Mar 2006 12:52:26 GMT, "jw 1111"
>Hi, am putting some new magnetic catches on to all my kitchen cupboard
>doors. ( the original spring type self-closing hinges are mostly very
>tired ).
>Since the door is actually shut when they are pressed together, you cannot
>just line them up by sight. Is there any trick for getting the metal plate
>lined up 'exactly' opposite the magnet catch?
Mostly what Newfie said. You will notice that most magnetic catches
what you buy have a pointed dimple on the plate. All you have to do
is install the magnet on the shelf, set it to protrude a little bit,
tighten the screws, put the plate on the magnet, and close the door
and press. The dimple will make an indent on the door, so that you
can place it accurately. Then simply bring the magnet back a bit.
--
Larry
rapp@lmr.com
|
| Similar Threads | Posted | | Thirteen-lined ground squirrels | November 12, 2007, 10:21 am |
| cupboard that won't stay shut | March 13, 2006, 2:23 pm |
| Above cupboard soffit insulation from attic | March 18, 2006, 12:12 am |
| Kitchen cupboard for guest house | March 6, 2007, 2:57 am |
| Kitchen Cupboard for guest house | March 6, 2007, 3:07 am |
| Refinishing kitchen cupboard doors. | January 9, 2009, 4:30 pm |
| Magnetic starters | December 13, 2006, 8:22 am |
| Magnetic Fridge Gasket | October 22, 2006, 11:55 pm |
| Magnetic Vent Cover | July 12, 2007, 4:00 pm |
| Magnetic vs electronic transformer? | April 6, 2008, 5:19 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> doors. ( the original spring type self-closing hinges are mostly very
> tired ).
> Since the door is actually shut when they are pressed together, you cannot
> just line them up by sight. Is there any trick for getting the metal plate
> lined up 'exactly' opposite the magnet catch?