If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by RBM on October 11, 2009, 6:34 pm
>>>>> I've been attempting to install a new ceiling fan in my bathroom. the
>>>>> motor in the old one started making noise, and it was about 20+ years
>>>>> old...so I figured an upgrade was in order.
>>>>> I live in an old loft building, where I access the fan from above my
>>>>> bathroom (there is a crawlspace above the bathroom) but the rest of
>>>>> the loft is open.
>>>>> I'm trying to not have to pull down the sheetrock in my bathroom in
>>>>> order to swap out this fan or otherwise make repairs. To be honest,
>>>>> I'm not the best with drywalling a ceiling..and that is a bit involved
>>>>> for just swapping out a ceiling fan right?
>>>>> Anyway...their is a piece of metal conduit that was running next to
>>>>> the old fan. I need to move that conduit by 2 inches in order for the
>>>>> new fan to fit. The metal conduit is connected to another piece about
>>>>> 3 inches behind the fan...my inclination is to disconnect the conduit
>>>>> from the extension, and replace it with a piece of flexible conduit.
>>>>> that will allow me to go nicely around the new fan.
>>>>> can I connect a piece of flex conduit to a piece of regular conduit (I
>>>>> assume I will use a junction box)?
>>>> There are transition fittings that will enable you to go from conduit
>>>> (EMT) to armored cable or flexible metallic conduit. Ask for a Type
>>>> EFC or EGC combination coupling. There's no reason to use a junction
>>>> box unless you will be cutting the wires and splicing.
>>> You can also make a "gofrom" using an EMT connector to a rigid pipe
>>> couping to a flex connector (assuming "metal conduit" is EMT). I would
>>> use a "Tomic" coupling, which is 1/2 length, but they are probably
>>> relatively hard to find.
>>>>> can I assume that because I have flex, I can run it diagonally and not
>>>>> have to worry that the wires won't make it?
>>>> No, that is your principal worry. Take a piece of string or wire and
>>>> lay it on the existing layout, then move it to where you want it to
>>>> be. If it doesn't quite make it, then you will have to go with plan B
>>>> and install a junction box.
>>> Or re-fish new wires.
>> I love the Tomic connectors and can't understand why they're so
>> hard to come by these days. I did a search and came up with a
>> two piece connector of the type you might see holding a power
>> cord on the back of a clothes dryer instead of the one piece
>> connector that you pop on the end of EMT. When I worked for an
>> electrical supply company in the early 70's we had them in stock.
>> The last time I saw any of them was at a missile range in the
>> late 80's. I wonder what happened to them.
> *I have no idea what a Tomic connector is. Using three search engines all
> I came up with is the two screw strain relief dryer cord connector clamp.
> Anyone have a picture or a link to a picture?
You kiddin me John, never heard of a Tomic connector, why it's a, a, well a
kind of connector, like, you know, metal with screws, or a, OK, OK, I give
up, I never heard of one either. Bud, draw us a picture
|
|
Posted by John Grabowski on October 11, 2009, 7:02 pm
>>>>>> I've been attempting to install a new ceiling fan in my bathroom.
>>>>>> the
>>>>>> motor in the old one started making noise, and it was about 20+ years
>>>>>> old...so I figured an upgrade was in order.
>>>>>> I live in an old loft building, where I access the fan from above my
>>>>>> bathroom (there is a crawlspace above the bathroom) but the rest of
>>>>>> the loft is open.
>>>>>> I'm trying to not have to pull down the sheetrock in my bathroom in
>>>>>> order to swap out this fan or otherwise make repairs. To be honest,
>>>>>> I'm not the best with drywalling a ceiling..and that is a bit
>>>>>> involved
>>>>>> for just swapping out a ceiling fan right?
>>>>>> Anyway...their is a piece of metal conduit that was running next to
>>>>>> the old fan. I need to move that conduit by 2 inches in order for
>>>>>> the
>>>>>> new fan to fit. The metal conduit is connected to another piece
>>>>>> about
>>>>>> 3 inches behind the fan...my inclination is to disconnect the conduit
>>>>>> from the extension, and replace it with a piece of flexible conduit.
>>>>>> that will allow me to go nicely around the new fan.
>>>>>> can I connect a piece of flex conduit to a piece of regular conduit
>>>>>> (I
>>>>>> assume I will use a junction box)?
>>>>> There are transition fittings that will enable you to go from conduit
>>>>> (EMT) to armored cable or flexible metallic conduit. Ask for a Type
>>>>> EFC or EGC combination coupling. There's no reason to use a junction
>>>>> box unless you will be cutting the wires and splicing.
>>>> You can also make a "gofrom" using an EMT connector to a rigid pipe
>>>> couping to a flex connector (assuming "metal conduit" is EMT). I would
>>>> use a "Tomic" coupling, which is 1/2 length, but they are probably
>>>> relatively hard to find.
>>>>>> can I assume that because I have flex, I can run it diagonally and
>>>>>> not
>>>>>> have to worry that the wires won't make it?
>>>>> No, that is your principal worry. Take a piece of string or wire and
>>>>> lay it on the existing layout, then move it to where you want it to
>>>>> be. If it doesn't quite make it, then you will have to go with plan B
>>>>> and install a junction box.
>>>> Or re-fish new wires.
>>> I love the Tomic connectors and can't understand why they're so
>>> hard to come by these days. I did a search and came up with a
>>> two piece connector of the type you might see holding a power
>>> cord on the back of a clothes dryer instead of the one piece
>>> connector that you pop on the end of EMT. When I worked for an
>>> electrical supply company in the early 70's we had them in stock.
>>> The last time I saw any of them was at a missile range in the
>>> late 80's. I wonder what happened to them.
>> *I have no idea what a Tomic connector is. Using three search engines
>> all I came up with is the two screw strain relief dryer cord connector
>> clamp. Anyone have a picture or a link to a picture?
> You kiddin me John, never heard of a Tomic connector, why it's a, a, well
> a kind of connector, like, you know, metal with screws, or a, OK, OK, I
> give up, I never heard of one either. Bud, draw us a picture
*I'm thinking that it is something that I know by another name.
|
|
Posted by RBM on October 11, 2009, 7:11 pm
>>>>>>> I've been attempting to install a new ceiling fan in my bathroom.
>>>>>>> the
>>>>>>> motor in the old one started making noise, and it was about 20+
>>>>>>> years
>>>>>>> old...so I figured an upgrade was in order.
>>>>>>> I live in an old loft building, where I access the fan from above my
>>>>>>> bathroom (there is a crawlspace above the bathroom) but the rest of
>>>>>>> the loft is open.
>>>>>>> I'm trying to not have to pull down the sheetrock in my bathroom in
>>>>>>> order to swap out this fan or otherwise make repairs. To be honest,
>>>>>>> I'm not the best with drywalling a ceiling..and that is a bit
>>>>>>> involved
>>>>>>> for just swapping out a ceiling fan right?
>>>>>>> Anyway...their is a piece of metal conduit that was running next to
>>>>>>> the old fan. I need to move that conduit by 2 inches in order for
>>>>>>> the
>>>>>>> new fan to fit. The metal conduit is connected to another piece
>>>>>>> about
>>>>>>> 3 inches behind the fan...my inclination is to disconnect the
>>>>>>> conduit
>>>>>>> from the extension, and replace it with a piece of flexible conduit.
>>>>>>> that will allow me to go nicely around the new fan.
>>>>>>> can I connect a piece of flex conduit to a piece of regular conduit
>>>>>>> (I
>>>>>>> assume I will use a junction box)?
>>>>>> There are transition fittings that will enable you to go from conduit
>>>>>> (EMT) to armored cable or flexible metallic conduit. Ask for a Type
>>>>>> EFC or EGC combination coupling. There's no reason to use a junction
>>>>>> box unless you will be cutting the wires and splicing.
>>>>> You can also make a "gofrom" using an EMT connector to a rigid pipe
>>>>> couping to a flex connector (assuming "metal conduit" is EMT). I would
>>>>> use a "Tomic" coupling, which is 1/2 length, but they are probably
>>>>> relatively hard to find.
>>>>>>> can I assume that because I have flex, I can run it diagonally and
>>>>>>> not
>>>>>>> have to worry that the wires won't make it?
>>>>>> No, that is your principal worry. Take a piece of string or wire and
>>>>>> lay it on the existing layout, then move it to where you want it to
>>>>>> be. If it doesn't quite make it, then you will have to go with plan
>>>>>> B
>>>>>> and install a junction box.
>>>>> Or re-fish new wires.
>>>> I love the Tomic connectors and can't understand why they're so
>>>> hard to come by these days. I did a search and came up with a
>>>> two piece connector of the type you might see holding a power
>>>> cord on the back of a clothes dryer instead of the one piece
>>>> connector that you pop on the end of EMT. When I worked for an
>>>> electrical supply company in the early 70's we had them in stock.
>>>> The last time I saw any of them was at a missile range in the
>>>> late 80's. I wonder what happened to them.
>>> *I have no idea what a Tomic connector is. Using three search engines
>>> all I came up with is the two screw strain relief dryer cord connector
>>> clamp. Anyone have a picture or a link to a picture?
>> You kiddin me John, never heard of a Tomic connector, why it's a, a, well
>> a kind of connector, like, you know, metal with screws, or a, OK, OK, I
>> give up, I never heard of one either. Bud, draw us a picture
> *I'm thinking that it is something that I know by another name.
That was my thought too. In this business, I go to an electrical supply
house outside of NY, and it's like I'm speaking a foreign language.
>
|
|
Posted by John Grabowski on October 12, 2009, 9:27 am
>>>>>>>> I've been attempting to install a new ceiling fan in my bathroom.
>>>>>>>> the
>>>>>>>> motor in the old one started making noise, and it was about 20+
>>>>>>>> years
>>>>>>>> old...so I figured an upgrade was in order.
>>>>>>>> I live in an old loft building, where I access the fan from above
>>>>>>>> my
>>>>>>>> bathroom (there is a crawlspace above the bathroom) but the rest of
>>>>>>>> the loft is open.
>>>>>>>> I'm trying to not have to pull down the sheetrock in my bathroom in
>>>>>>>> order to swap out this fan or otherwise make repairs. To be
>>>>>>>> honest,
>>>>>>>> I'm not the best with drywalling a ceiling..and that is a bit
>>>>>>>> involved
>>>>>>>> for just swapping out a ceiling fan right?
>>>>>>>> Anyway...their is a piece of metal conduit that was running next to
>>>>>>>> the old fan. I need to move that conduit by 2 inches in order for
>>>>>>>> the
>>>>>>>> new fan to fit. The metal conduit is connected to another piece
>>>>>>>> about
>>>>>>>> 3 inches behind the fan...my inclination is to disconnect the
>>>>>>>> conduit
>>>>>>>> from the extension, and replace it with a piece of flexible
>>>>>>>> conduit.
>>>>>>>> that will allow me to go nicely around the new fan.
>>>>>>>> can I connect a piece of flex conduit to a piece of regular conduit
>>>>>>>> (I
>>>>>>>> assume I will use a junction box)?
>>>>>>> There are transition fittings that will enable you to go from
>>>>>>> conduit
>>>>>>> (EMT) to armored cable or flexible metallic conduit. Ask for a Type
>>>>>>> EFC or EGC combination coupling. There's no reason to use a
>>>>>>> junction
>>>>>>> box unless you will be cutting the wires and splicing.
>>>>>> You can also make a "gofrom" using an EMT connector to a rigid pipe
>>>>>> couping to a flex connector (assuming "metal conduit" is EMT). I
>>>>>> would use a "Tomic" coupling, which is 1/2 length, but they are
>>>>>> probably relatively hard to find.
>>>>>>>> can I assume that because I have flex, I can run it diagonally and
>>>>>>>> not
>>>>>>>> have to worry that the wires won't make it?
>>>>>>> No, that is your principal worry. Take a piece of string or wire
>>>>>>> and
>>>>>>> lay it on the existing layout, then move it to where you want it to
>>>>>>> be. If it doesn't quite make it, then you will have to go with plan
>>>>>>> B
>>>>>>> and install a junction box.
>>>>>> Or re-fish new wires.
>>>>> I love the Tomic connectors and can't understand why they're so
>>>>> hard to come by these days. I did a search and came up with a
>>>>> two piece connector of the type you might see holding a power
>>>>> cord on the back of a clothes dryer instead of the one piece
>>>>> connector that you pop on the end of EMT. When I worked for an
>>>>> electrical supply company in the early 70's we had them in stock.
>>>>> The last time I saw any of them was at a missile range in the
>>>>> late 80's. I wonder what happened to them.
>>>> *I have no idea what a Tomic connector is. Using three search engines
>>>> all I came up with is the two screw strain relief dryer cord connector
>>>> clamp. Anyone have a picture or a link to a picture?
>>> You kiddin me John, never heard of a Tomic connector, why it's a, a,
>>> well a kind of connector, like, you know, metal with screws, or a, OK,
>>> OK, I give up, I never heard of one either. Bud, draw us a picture
>> *I'm thinking that it is something that I know by another name.
> That was my thought too. In this business, I go to an electrical supply
> house outside of NY, and it's like I'm speaking a foreign language.
*LOL. When I lived on the west coast it took me a while to learn the
language of the trade out there. One thing that is universal though is the
numbers. If I give the counterman a manufacturer name and part number he
has no trouble understanding what I want. Having it in stock is another
issue.
|
|
Posted by bob haller on October 12, 2009, 10:54 am
replacemnt motors are available, might be worth the effort to save
LOTS of mucking around modifying opening to fit new fan
|
Page 2 of 5 < 1 2 3 > last >>
| Similar Threads | Posted | | Electrical Conduit Depth? | June 20, 2006, 8:34 am |
| 1/2" electrical PVC conduit question | February 12, 2009, 9:31 pm |
| Underground electrical conduit | August 24, 2009, 5:30 pm |
| Adding or moving an electrical outlet | October 5, 2006, 1:43 pm |
| Filling up space around electrical conduit | February 24, 2006, 4:40 pm |
| PVC water pipe for electrical conduit | September 20, 2009, 4:03 pm |
| Moving Bathroom 3-arm sconce - Electrical Question | March 12, 2007, 2:00 pm |
| Electrical: making rainproof conduit connections | September 8, 2006, 1:36 pm |
| Electrical Conduit through concrete stem wall | August 28, 2007, 1:20 pm |
| Rerouting an 1/2" rigid electrical conduit in the attic | February 7, 2009, 9:14 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>>>>> motor in the old one started making noise, and it was about 20+ years
>>>>> old...so I figured an upgrade was in order.
>>>>> I live in an old loft building, where I access the fan from above my
>>>>> bathroom (there is a crawlspace above the bathroom) but the rest of
>>>>> the loft is open.
>>>>> I'm trying to not have to pull down the sheetrock in my bathroom in
>>>>> order to swap out this fan or otherwise make repairs. To be honest,
>>>>> I'm not the best with drywalling a ceiling..and that is a bit involved
>>>>> for just swapping out a ceiling fan right?
>>>>> Anyway...their is a piece of metal conduit that was running next to
>>>>> the old fan. I need to move that conduit by 2 inches in order for the
>>>>> new fan to fit. The metal conduit is connected to another piece about
>>>>> 3 inches behind the fan...my inclination is to disconnect the conduit
>>>>> from the extension, and replace it with a piece of flexible conduit.
>>>>> that will allow me to go nicely around the new fan.
>>>>> can I connect a piece of flex conduit to a piece of regular conduit (I
>>>>> assume I will use a junction box)?
>>>> There are transition fittings that will enable you to go from conduit
>>>> (EMT) to armored cable or flexible metallic conduit. Ask for a Type
>>>> EFC or EGC combination coupling. There's no reason to use a junction
>>>> box unless you will be cutting the wires and splicing.
>>> You can also make a "gofrom" using an EMT connector to a rigid pipe
>>> couping to a flex connector (assuming "metal conduit" is EMT). I would
>>> use a "Tomic" coupling, which is 1/2 length, but they are probably
>>> relatively hard to find.
>>>>> can I assume that because I have flex, I can run it diagonally and not
>>>>> have to worry that the wires won't make it?
>>>> No, that is your principal worry. Take a piece of string or wire and
>>>> lay it on the existing layout, then move it to where you want it to
>>>> be. If it doesn't quite make it, then you will have to go with plan B
>>>> and install a junction box.
>>> Or re-fish new wires.