Home Page link

natural gas furnace won't stay on

Home Repair - - If it ain't broken, don't fix it. Otherwise look here. 

Bookmark this page:  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
natural gas furnace won't stay on frank1711 01-19-2007
If you were  Registered and logged in, you could reply and use other advanced thread options
Posted by on January 19, 2007, 2:47 am


I have a natural gas furnace that won't stay on. The pilot is lit and
the burners come on, a few seconds later the fan starts and runs for no
more than a minute and then it stops. The burners sometimes go out
before the fan stops or the fan never comes on at all. I can turn the
fan on at the control and have it run with out a problem, but that is
just circulating the air and not heating it. I think the fan is
controlled by it's own thermostat. Once the thermostat in the house
starts the burners a thermostat in the furnace turns on the fan when it
reaches a certain temp to blow the warm air through the ducts. Does
this sound right? Could this be where my problem lies? Could it be as
simple as a loose wire to that particular thermostat? We had a service
guy come and look at it and tell it us it's just old & inefficient and
it'll be about a grand to replace. I had the Gas Company out last week
to replace my meter with a higher flow model due to a recent swimming
pool installation. He checked all our gas appliances after the
replacement and everything including the furnace worked fine. The
furnace started having trouble over a week later, I doubt the problem
was caused or triggered by anything he did since the furnace worked
fine for over a week. Help a cold Californian please, yes it gets cold
in CA. I'm in SoCal, high desert area, last weekend we had single digit
temps (rare). Thank God it worked then.


Posted by buffalobill on January 19, 2007, 3:52 am


in buffalo ny: on my 1990 gas boiler, the spark ignitor is also a flame
sensor. on mine i have to see that pilot flame wraps around the
sensor/ignitor/thermocouple properly after the ignition spark and
during the main burner on. and exactly according to the specifications
of the manufacturer. i keep my manual by the boiler.
if there is a good flame then i replace the ignitor/sensor.
if i have insufficient flame, i clean out or replace the pilot
assembly.
see:
http://www.arnoldservice.com/Troubleshooting_Heating_Problems.htm
and:
http://toad.net/~jsmeenen/gasvalve.html


frank1711@aol.com wrote:
> I have a natural gas furnace that won't stay on. The pilot is lit and
> the burners come on, a few seconds later the fan starts and runs for no
> more than a minute and then it stops. The burners sometimes go out
> before the fan stops or the fan never comes on at all. I can turn the
> fan on at the control and have it run with out a problem, but that is
> just circulating the air and not heating it. I think the fan is
> controlled by it's own thermostat. Once the thermostat in the house
> starts the burners a thermostat in the furnace turns on the fan when it
> reaches a certain temp to blow the warm air through the ducts. Does
> this sound right? Could this be where my problem lies? Could it be as
> simple as a loose wire to that particular thermostat? We had a service
> guy come and look at it and tell it us it's just old & inefficient and
> it'll be about a grand to replace. I had the Gas Company out last week
> to replace my meter with a higher flow model due to a recent swimming
> pool installation. He checked all our gas appliances after the
> replacement and everything including the furnace worked fine. The
> furnace started having trouble over a week later, I doubt the problem
> was caused or triggered by anything he did since the furnace worked
> fine for over a week. Help a cold Californian please, yes it gets cold
> in CA. I'm in SoCal, high desert area, last weekend we had single digit
> temps (rare). Thank God it worked then.


Posted by Roby on January 19, 2007, 6:55 am


frank1711@aol.com wrote:

> I have a natural gas furnace that won't stay on. The pilot is lit and
> the burners come on, a few seconds later the fan starts and runs for no
> more than a minute and then it stops. The burners sometimes go out
> before the fan stops or the fan never comes on at all. I can turn the
> fan on at the control and have it run with out a problem, but that is
> just circulating the air and not heating it. I think the fan is
> controlled by it's own thermostat. Once the thermostat in the house
> starts the burners a thermostat in the furnace turns on the fan when it
> reaches a certain temp to blow the warm air through the ducts. Does
> this sound right? Could this be where my problem lies? Could it be as
> simple as a loose wire to that particular thermostat? We had a service
> guy come and look at it and tell it us it's just old & inefficient and
> it'll be about a grand to replace. I had the Gas Company out last week
> to replace my meter with a higher flow model due to a recent swimming
> pool installation. He checked all our gas appliances after the
> replacement and everything including the furnace worked fine. The
> furnace started having trouble over a week later, I doubt the problem
> was caused or triggered by anything he did since the furnace worked
> fine for over a week. Help a cold Californian please, yes it gets cold
> in CA. I'm in SoCal, high desert area, last weekend we had single digit
> temps (rare). Thank God it worked then.
There's a safety thermostat in the furnace that is intended to shut down
on furnace overtemperature. If yours is failing or has a loose connection,
it might be the culprit. Or you could just replace the whole furnace.
Or move (further) south.

Posted by Felder on January 19, 2007, 3:17 pm



frank1711@aol.com wrote:
> I have a natural gas furnace that won't stay on. The pilot is lit and
> the burners come on, a few seconds later the fan starts and runs for no
> more than a minute and then it stops. The burners sometimes go out
> before the fan stops or the fan never comes on at all. I can turn the
> fan on at the control and have it run with out a problem, but that is
> just circulating the air and not heating it. I think the fan is
> controlled by it's own thermostat. Once the thermostat in the house
> starts the burners a thermostat in the furnace turns on the fan when it
> reaches a certain temp to blow the warm air through the ducts. Does
> this sound right? Could this be where my problem lies? Could it be as
> simple as a loose wire to that particular thermostat? We had a service
> guy come and look at it and tell it us it's just old & inefficient and
> it'll be about a grand to replace. I had the Gas Company out last week
> to replace my meter with a higher flow model due to a recent swimming
> pool installation. He checked all our gas appliances after the
> replacement and everything including the furnace worked fine. The
> furnace started having trouble over a week later, I doubt the problem
> was caused or triggered by anything he did since the furnace worked
> fine for over a week. Help a cold Californian please, yes it gets cold
> in CA. I'm in SoCal, high desert area, last weekend we had single digit
> temps (rare). Thank God it worked then.


Could be the fan control is set too high and just needs tweaked down a
little.
-Felder


Similar ThreadsPosted
Air Circulation for Natural Gas Furnace August 16, 2006, 7:04 am
Natural Gas Furnace Clicking Noise January 1, 2006, 10:10 pm
converting a furnace from natural gas to propane September 21, 2006, 6:19 pm
Replace Natural Gas Forced Air Central Furnace January 24, 2007, 10:25 pm
Natural Gas Furnace & Water Heater Upgrade. April 6, 2007, 12:08 pm
Window Will Not Stay Up May 30, 2006, 6:01 am
Thermocoupler won't stay lit July 7, 2006, 12:47 pm
Window does not stay up September 19, 2006, 3:23 pm
Can you stay for 18sec, try!! December 27, 2006, 6:48 pm
Home to stay February 3, 2008, 11:02 am

Contact Us | Privacy Policy

XML SitemapXML Sitemap