If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by rachelms79 on July 22, 2005, 9:58 am
Sorry for the simple question, but when you buy a toilet tank in Home
Depot, etc.
does the tank have the fill valve and flush valve already in place or
does the installer have to put them in?
The reason I'm asking is that last Monday I had a plumber (actually 2
newbie-looking guys came) install a new Kohler Wellworth toilet that I
got at HD but I didn't open the boxes before to see if the tank
components were pre-installed. The problem is that now the tank leaks
to the bowl, about 3-4 gallons a day. I looked inside the tank and the
arrangement of components seems odd to me (e.g. the vertical rod on the
Fluidmaster-type fill valve is rubbing against the horizontal rod of
the flush handle). I was wondering if maybe the plumber put these
components in, if he didn't tighten them enough or if the fill valve
should be facing the flush valve instead of facing front.
I also noticed that one of the guys connected the tank to the bowl on
the carpet in the bedroom outside the bathroom, while the other guy was
removing the old toilet. Then together they carried the new toilet into
the bathroom. The Kohler install instructions say to install the bowl
first and then the tank. Does this make a big difference in the
tightness of the tank/bowl connection?
I called Kohler and they said to tighten the nuts on the tank. I'm not
that handy, so should I call the plumber back to tighten them?
Thanks much.
|
|
Posted by kevin on July 22, 2005, 10:50 am
Can't answer most of your questions. But, tightening the nuts is just a
few seconds job if you have a pliers or socket wrench. But then again,
this is not going to stop any leak, unless the leak is on to the floor.
Sounds to me that some of the components are not quite adjusted right,
or need some fiddling to get aligned right. From the sound of it, you
don't want to deal with this, and you shouldn't have to. Call the
plumbers and complain. Toilets should not leak like that.
BTW -- how the heck can you tell that it is 3 or 4 gallons?
|
|
Posted by sleepdog on July 22, 2005, 11:40 am
Could be a deformed flapper or flapper seat at the bottom of the tank.
I bought a brand new Kohler one piece low profile toilet from HD and it
leaked through the flapper from day one. And both replacement flappers
I bought did not fit like the original so I wasted a few more dollars.
I decided to ignore the faint dripping sound since the tank wasn't ever
refilling itself.
|
|
Posted by evodawg on July 22, 2005, 6:27 pm
rachelms79@hotmail.com wrote:
show/hide quoted text
> Sorry for the simple question, but when you buy a toilet tank in Home
> Depot, etc.
> does the tank have the fill valve and flush valve already in place or
> does the installer have to put them in?
>
> The reason I'm asking is that last Monday I had a plumber (actually 2
> newbie-looking guys came) install a new Kohler Wellworth toilet that I
> got at HD but I didn't open the boxes before to see if the tank
> components were pre-installed. The problem is that now the tank leaks
> to the bowl, about 3-4 gallons a day. I looked inside the tank and the
> arrangement of components seems odd to me (e.g. the vertical rod on the
> Fluidmaster-type fill valve is rubbing against the horizontal rod of
> the flush handle). I was wondering if maybe the plumber put these
> components in, if he didn't tighten them enough or if the fill valve
> should be facing the flush valve instead of facing front.
>
> I also noticed that one of the guys connected the tank to the bowl on
> the carpet in the bedroom outside the bathroom, while the other guy was
> removing the old toilet. Then together they carried the new toilet into
> the bathroom. The Kohler install instructions say to install the bowl
> first and then the tank. Does this make a big difference in the
> tightness of the tank/bowl connection?
>
> I called Kohler and they said to tighten the nuts on the tank. I'm not
> that handy, so should I call the plumber back to tighten them?
>
> Thanks much.
The flush mech. is usually already installed in the tank. All you have to do
is make sure you tighten the tank to the bowl just enough to get a good
seal between them and install the toilet onto the waste trap with a wax
ring and connect the water supply. They may have turned the inside mech.
while tightening the water supply to the tank. And the reason your leaking
may be because the seal between the tank and bowl is not lined up or not
tight enough
Rich
|
|
Posted by James \"Cubby\" Culbertson on July 22, 2005, 8:33 pm
Good grief! You paid for someone to do the install and it's not right.
Call them back and let them fix it. You can fiddle with tightening bolts
etc but what happens when/if you crack the tank? You're out the cost of
two toilets and installs. I rarely pay anyone to do work on or around my
house but when I do, if it isn't what I expected, then I call them back.
Cheers,
show/hide quoted text
> Sorry for the simple question, but when you buy a toilet tank in Home
> Depot, etc.
> does the tank have the fill valve and flush valve already in place or
> does the installer have to put them in?
> The reason I'm asking is that last Monday I had a plumber (actually 2
> newbie-looking guys came) install a new Kohler Wellworth toilet that I
> got at HD but I didn't open the boxes before to see if the tank
> components were pre-installed. The problem is that now the tank leaks
> to the bowl, about 3-4 gallons a day. I looked inside the tank and the
> arrangement of components seems odd to me (e.g. the vertical rod on the
> Fluidmaster-type fill valve is rubbing against the horizontal rod of
> the flush handle). I was wondering if maybe the plumber put these
> components in, if he didn't tighten them enough or if the fill valve
> should be facing the flush valve instead of facing front.
> I also noticed that one of the guys connected the tank to the bowl on
> the carpet in the bedroom outside the bathroom, while the other guy was
> removing the old toilet. Then together they carried the new toilet into
> the bathroom. The Kohler install instructions say to install the bowl
> first and then the tank. Does this make a big difference in the
> tightness of the tank/bowl connection?
> I called Kohler and they said to tighten the nuts on the tank. I'm not
> that handy, so should I call the plumber back to tighten them?
> Thanks much.
>
|
| Similar Threads | Posted | | Fill Valve for Kohler One-Piece Toilet? | January 9, 2006, 12:15 am |
| Replace fill valve in toilet tank, simple fix right? | September 6, 2009, 12:35 pm |
| Kohler Rialto One Piece Toilet Leaks | November 29, 2005, 8:08 pm |
| How to get the tank lid off a Kohler top-trip toilet? | October 7, 2005, 2:26 pm |
| Toilet Tank Leaks When I Lean Back | October 12, 2006, 4:51 pm |
| Toilet tank flap valve problems. | March 26, 2006, 10:27 pm |
| toilet tank shut off valve question | June 27, 2006, 5:26 pm |
| Unusual toilet tank flush valve repair? | June 7, 2009, 8:46 pm |
| Kohler Flush Valve(Flapper) | November 13, 2006, 9:24 am |
| Leaky Kohler shower valve | December 29, 2006, 4:19 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> Depot, etc.
> does the tank have the fill valve and flush valve already in place or
> does the installer have to put them in?
>
> The reason I'm asking is that last Monday I had a plumber (actually 2
> newbie-looking guys came) install a new Kohler Wellworth toilet that I
> got at HD but I didn't open the boxes before to see if the tank
> components were pre-installed. The problem is that now the tank leaks
> to the bowl, about 3-4 gallons a day. I looked inside the tank and the
> arrangement of components seems odd to me (e.g. the vertical rod on the
> Fluidmaster-type fill valve is rubbing against the horizontal rod of
> the flush handle). I was wondering if maybe the plumber put these
> components in, if he didn't tighten them enough or if the fill valve
> should be facing the flush valve instead of facing front.
>
> I also noticed that one of the guys connected the tank to the bowl on
> the carpet in the bedroom outside the bathroom, while the other guy was
> removing the old toilet. Then together they carried the new toilet into
> the bathroom. The Kohler install instructions say to install the bowl
> first and then the tank. Does this make a big difference in the
> tightness of the tank/bowl connection?
>
> I called Kohler and they said to tighten the nuts on the tank. I'm not
> that handy, so should I call the plumber back to tighten them?
>
> Thanks much.