|
Home Repair - - If it ain't broken, don't fix it. Otherwise look here.
|
|
|
|
If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on July 9, 2007, 1:19 pm
i have a craftsman garage door opener, approximately 17 years old.
i've noticed the chain is sagging and the door only opens up 1/2 way
due to it getting stuck or caught on something - can anyone help with
this problem? we've had the springs replaced and that doesn't seem to
be the problem, just the sagging chain.
|
 
| |
Posted by Jeff Wisnia on July 9, 2007, 3:02 pm
stewey7@hotmail.com wrote:
> i have a craftsman garage door opener, approximately 17 years old.
> i've noticed the chain is sagging and the door only opens up 1/2 way
> due to it getting stuck or caught on something - can anyone help with
> this problem? we've had the springs replaced and that doesn't seem to
> be the problem, just the sagging chain.
>
There should be an adjuster which lets you take the wear slack out of
the chain/cable. On my Crapsman openers it's built into the traveling
carriage to which the door arm attaches.
Look for it, and do what it takes to tighten up the chain a bit.
HTH,
Jeff
--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.
|
|
Posted by doordoc@prodigy.net on July 9, 2007, 5:20 pm
On Jul 9, 1:19 pm, stew...@hotmail.com wrote:
> i have a craftsmangaragedooropener, approximately 17 years old.
> i've noticed the chain is sagging and thedooronly opens up 1/2 way
> due to it getting stuck or caught on something - can anyone help with
> this problem? we've had the springs replaced and that doesn't seem to
> be the problem, just the sagging chain.
With the door disconnected from the opener (no load) there should be
approx 1/2" of sag in the chain.
As usual, the first thing to try is to disconnect the door & open the
door by hand to see if it opens easily & freely. If it doesn't look
for something catching the door by the track (like broom handle, etc
or the door lock partially engaged. If it does move freely run the
opener w/ the door still disconnected to see if it stops without any
load.
Does it open exactly half way or is it stopping where the rail is
spliced together (usually 1/3 & 2/3). If it's stopping at the splice
bend the four taps up slightly on the inner carriage (part that door
arm connects to). These tend to catch on the splice, but don't bend
them up to much or the outer carriage part won't go past them to re-
connect the door.
Inspect the the shaft & the motor head sprocket on top of the unit
that the chain goes around. The sprocket is welded to the shaft & they
have been known to separate from the shaft & they bend upward until
they break completely. Also make sure that the shaft is pointing
straight up & down. If it appears that it is leaning toward the door
the bearing that the shaft is going through is probably worn out. This
is another known problem & over-tightening the chain or a heavy door
will make the problem occur even sooner then normal. This part is an
assembly that includes the shaft, chain sprocket, bearing plate, &
plastic drive gear, but does not include the limit gear sprocket at
the bottom of the shaft. After you remove the limit gear & the 3
screws holding the bearing to the motor head the whole assembly lifts
out from the top. If you remove the chain do not move it until you put
it back on the sprocket & put it back as close to the spot as
possible. If you move it to much or run the opener without the chain,
you will have a heck of a time getting the limits reset. Also please
note that the 3 screws holding the bearing plate are a metric size.
Yes there is a threaded rod on the chain to tighten it, but only
tighten the chain in this manner after you have verified that there
isn't something else causing the chain to sag.
DoorDoc
www.ActionDoor.com
|
| Similar Threads | Posted | | Problem removing chain from Sears chain saw | May 10, 2006, 12:30 pm |
| Poulan pro 44cc 20" chain saw - chain oil not feeding | May 6, 2008, 2:50 pm |
| Sagging Wall | February 15, 2006, 9:46 pm |
| How much sagging is acceptable? | December 11, 2006, 1:37 pm |
| Sagging Roof | June 22, 2007, 1:34 pm |
| Roof Sagging | September 1, 2007, 8:50 pm |
| Sagging door? | May 31, 2008, 1:39 am |
| Re: What is the best way to fix a sagging gate? | June 29, 2008, 10:20 pm |
| Lifting sagging deck | April 12, 2006, 10:53 am |
| sagging floor in berkeley | December 29, 2006, 6:32 pm |
|
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap