toilet flange

	toilet flange

Home| Search | About

Lost Password?

Home Repair - - If it ain't broken, don't fix it. Otherwise look here.

Bookmark this page: YahooMyWeb

Yahoo!

Google

Windows Live

del.icio.us digg

digg

Netscape

Subject

Author

Date

toilet flange

stonecreek

06-24-2008

mkerna

S. Barker

Paul Franklin

Colbyt

If you were Registered and logged in, you could reply and use other advanced thread options

Posted by stonecreek on June 24, 2008, 8:41 pm

I'm working on remodeling a small bathroom. When I removed the toilet, I
discovered that the circular metal piece on the toilet flange is pretty much
toast. The nails that went into the floor were rusted badly, the floor has
some rot, but it looks like the flange is glued into the PVC below. I can
access this from the basement, can probably replace the rotted plywood
floor, but how can that flange be replaced if it is glued into the PVC
below. It is on the outside of the PVC. There isn't much room to cut the
existing drain pipe and put new pieces back in place. This seems like it
would be a common problem in older homes and I don't understand why this
flange would be glued to the PVC underneath. Is their an alternative way to
fix this.

Any ideas would be appreciated.
Thanks

Posted by on June 24, 2008, 10:19 pm

The flange is PVC too? If it's PVC it's guaranteed to be glued. One
piece fits into the piece below it. If you don't have much room you
might be able to use a rubber sleeve; it joins two sections of pipe by
slipping over each and there's a band clamp on each end to be
tightened.

Mike

Posted by S. Barker on June 24, 2008, 10:34 pm

if the flange is too close to the first elbow to cut it and put in a
coupling, then you have to cut out the elbow also, and work back 'till you
have a long enough straight piece to couple up to. then work back towards
the flange with new pieces.

s

> I'm working on remodeling a small bathroom. When I removed the toilet, I

> discovered that the circular metal piece on the toilet flange is pretty

> much toast. The nails that went into the floor were rusted badly, the

> floor has some rot, but it looks like the flange is glued into the PVC

> below. I can access this from the basement, can probably replace the

> rotted plywood floor, but how can that flange be replaced if it is glued

> into the PVC below. It is on the outside of the PVC. There isn't much

> room to cut the existing drain pipe and put new pieces back in place.

> This seems like it would be a common problem in older homes and I don't

> understand why this flange would be glued to the PVC underneath. Is their

> an alternative way to fix this.

> Any ideas would be appreciated.

> Thanks

Posted by Paul Franklin on June 24, 2008, 11:28 pm

On Tue, 24 Jun 2008 21:34:35 -0500, "S. Barker"

>if the flange is too close to the first elbow to cut it and put in a

>coupling, then you have to cut out the elbow also, and work back 'till you

>have a long enough straight piece to couple up to. then work back towards

>the flange with new pieces.

>> I'm working on remodeling a small bathroom. When I removed the toilet, I

>> discovered that the circular metal piece on the toilet flange is pretty

>> much toast. The nails that went into the floor were rusted badly, the

>> floor has some rot, but it looks like the flange is glued into the PVC

>> below. I can access this from the basement, can probably replace the

>> rotted plywood floor, but how can that flange be replaced if it is glued

>> into the PVC below. It is on the outside of the PVC. There isn't much

>> room to cut the existing drain pipe and put new pieces back in place.

>> This seems like it would be a common problem in older homes and I don't

>> understand why this flange would be glued to the PVC underneath. Is their

>> an alternative way to fix this.

>> Any ideas would be appreciated.

>> Thanks

You can cut off the old flange and replace it with a special repair
flange that fits inside the closet elbow. Probably need to go to a
real plumbing supply house to get one. If the flange is high enough
you can cut it off using a hacksaw blade, but I usually use a dremel
with one of those little saw blades and slice it off from the inside.
I think you can only get the inside mounting flanges for 4" pipe. If
your closet el is 3" this won't work.

Sometimes, once you've cut the flange off as above, you can carefully
chisel off the remaining collar of the old flange, clean up the closet
el and glue on a new flange. But only try this if you are able to
replace the closet el should it crack when you're attempting to remove
the old flange collar.

HTH,

Paul

Posted by Colbyt on June 25, 2008, 4:29 pm